Chamberlain CSW24U Скачать руководство пользователя | Manualshive

Страница: 9 / 60

background image

7

GATE

CONDUIT & CONCRETE PAD

Gate must be constructed and installed according to ASTM F2200
standards (refer to page 4). Gate must fit specifications of operator
(refer to specifications).

Trench and install conduit. Before trenching, contact underground
utility locating companies. Conduit must be UL approved for low and
high voltage. Consider the operator placement BEFORE installing the
pad or post.

Concrete Pads

SAFETY

Entrapment protection devices are required to protect against any
entrapment or safety conditions encountered in your gate application.
Install warning signs on both sides of the gate.

Warning Signs

Entrapment Danger

VEHICLE LOOPS

The vehicle loops allow the gate to stay open when vehicles are
obstructing the gate path. Suggested for vehicles 14 feet (4.27 m) or
longer. Vehicle loops are not required but are recommended.

(Inside Property)

SITE PREPARATION

Check the national and local building codes

BEFORE

installation.

INTRODUCTION

CHECK YOUR GATE

Gate MUST be level. Gate and gate
post MUST be plumb. Gate MUST
have smooth bottom edge, no
protrusions should exist.

Remove ANY/ALL wheels
from the bottom of gate.

Gate MUST NOT hit or drag
across the ground.

Gate MUSTswing freely and
be supported entirely by its
hinges.

«
...
7
8
9
10
11
...
»

Содержание CSW24U





























































Отзывы:

Нет отзывов

Похожие инструкции для CSW24U

Бренд: FAAC Страницы: 17

Бренд: FAAC Страницы: 8

Бренд: GiBiDi Страницы: 16

Бренд: Calimet Страницы: 24

Бренд: FAAC Страницы: 14

Бренд: Ginnys Страницы: 8

Бренд: Telcoma Automations Страницы: 68

Бренд: LOBAS Страницы: 56

Бренд: Black & Decker Страницы: 8

Gizmo EM200 Series

Бренд: Black & Decker Страницы: 2

Бренд: Nice Страницы: 16

Бренд: Nice Страницы: 31

Бренд: Nice Страницы: 20

Бренд: Nice Страницы: 184

Бренд: Nice Страницы: 98

Бренд: Wisniowski Страницы: 80

Бренд: FAAC Страницы: 44

Security+ 3110C

Бренд: Chamberlain Страницы: 72

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды