manualshive.com logo in svg

Centrometal Cm-SOL, Технические инструкции

Поделиться
Скачать
Centrometal Cm-SOL Скачать руководство пользователя страница 66

66

E

E

E

R

R

R

Technical instructions 

Cm

-SOL

8.x.x.8. Sensor type

If NTC sensor is installed, here it must be changed from PT1000 to NTC 
type.

Sensor type

PT1000

Factory settings

PT1000/NTC

8.x.x. Boiler 2

Menus for conventional heating source 2 settings. All menus are similar 
to menus for conventional heating source 1 and will not be separately 
explained here (for details, see 8.4.2. Boiler 1).

8.x.x. Heating delay

For  this  menu  to  appear,  minimun  one  of  the  conventional  heating 
source must be set.
If the function is enabled and collector pump is active (tank is filled with 
solar energy) this function lowers the temperature of activation of the  
conventional heating source function (delays start of the conventional 
heating  source  function)  by  value  that  is  set  under  Lowering 
temperature menu.
If collector pump is active, delay start of the heating:
[Ttank_upper1 <= TDHW -dTboiler_tank - 

Tlowering temperature

].

If  collector  pump  isn’t  active  a  tank  needs  to  be  heated,  delay  isn’t 
considered:
[Ttank_upper1 <= TDHW -dTboiler_tank].

Heating delay

OFF

Factory settings

OFF/ON

Lowering temperature

0

Factory settings

min./max.

0 / 90

°C

8.x.x.1. Heating delay

In this menu heating delay can be enabled or disabled.

8.x.x.2. Lowering temperature

Setting the temperature for which start of the heating with convenctional 
heating source will be delayed when collector pump is working.

8.x. Recirculation

In this menu are additional menus for setting the recirculation of DHW.

In this menus work and pause time of the DHW recirculation pump can 
be set and also set the time interval when work and pause will be active.

8.x.1. Recirculation

In this menu recirculation function can be enabled or disabled. All set 
times and schedules remains valid.

Recirculation

OFF

Factory settings

OFF/ON

Installation, tank heating, recirculation

8.5. RECIRCULATION

selection

selection

unit.

unit.

Содержание Cm-SOL

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды