manualshive.com logo in svg

Centrometal Cm-SOL, Технические инструкции

Поделиться
Скачать
Centrometal Cm-SOL Скачать руководство пользователя страница 64

64

Technical instructions 

Cm

-SOL

8.x. DHW heating

8.x. DHW heating

In  this  menu  are  additional  menus  for  setting  the  heating  with  the 
conventional heating sources connected to tank 1.

8.x.x. Electric heater

In this menu are additional menus for setting the heating with the electric 
heater.

Electric heater

OFF

Factory settings

OFF/ON

8.x.x.1. Electric heater

In this menu electric heater can be switch ON or OFF

8.x.x. Boiler 1

In this menu are addtional settings for heating with conventional source 
1.

8.x.x.1. Boiler 1

In  this  menu  for  heating  with  conventional  heating  source  1  can  be 
enabled  or  disabled  (ie.  work  of  pump  between  conventional  heat 
source and tank 1).

8.x.x.2. T MAX Boiler 1

Setting of the maximum temperature of the conventional heating source 
1. If the temperature in conventional heating source is higher than set, 
pump to the tank will not start.

T MAX Boiler 1

90

Factory settings

min./max.

30 / 90

°C

Boiler 1

OFF

Factory settings

OFF/ON

8.4.2.3. TD boiler1-tank1 (difference)

Setting  of  the  temperature  difference  between  conventional  heating 
source 1 and first tank (upper sensor) for start and stop of the pump 
between boiler 1 and tank 1. Some of the conditions:

pump start: [Tboiler1=>

TDboiler1-tank

+5]

pump stop: [Tboiler1=<

TDboiler1-tank

]

TD boiler1-tank

10

Factory settings

min./max.

3 / 20

°C

8. . .4. TH boiler1-tank1 (hysteresis)

x x

Setting the temperature hysteresis between conventional heating source 1 
and fist tank (upper sensor) for start of the pump between boiler 1 and tank 
1. Some of the conditions:

pump start: [Ttank1upper<TDHW-

-T

]

THboiler1-tank

lowering temperature

TH boiler1-tank

10

Factory settings

min./max.

3 / 20

°C

Installation, tank heating

example: configurated 1 electric heater and
                2 conventional heating sources

selection

selection

unit.

unit.

unit.

Содержание Cm-SOL

































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды