Cary Audio Design HD Surround Sound Processor Cinema 11a Скачать руководство пользователя страница 36

Страница: 36 / 59

MANUAL SOUND SETUP

Press the

button on the remote until you reach “SET BALANCE” on the front panel

display.
The “MOVIE SPK Setting / Set Balance” menu appears on the front panel display.

Press the ENTER button on the remote to enter the “SET BALANCE” menu.

The “SET BALANCE / TEST MODE.....Off” menu appears on the front panel display.

Press the

button on the remote to select between manual or auto test tones, or to

turn the test tones off completely.

By selecting MANUAL, a special test tone will be generated as you move through each

speaker, allowing you to measure the output of the speaker that's playing.

Press the

button on the remote until you reach FL (FRONT LEFT) on the front panel

display.

The “Set Balance / FL……0.0dB” menu appears on the front panel display.

Use the

and

buttons on the remote to adjust the speaker level.

You can adjust the selected channel level in 0.5dB steps across a range of -15dB to +

15dB. The recommended calibration level is 75dB/SPL as displayed on the meter.

Press the

button on the remote when you have finished making the FRONT LEFT

level adjustment. Repeat steps 7 and 8 until you have completed setting the appropriate

level for each speaker within your system. Set all the levels to the 75dB reference level

on your meter.

10.

When you have finished adjusting the levels for all of the speakers within your system,
press the

button on the remote to select BACK, then press ENTER to return to the

previous “SETUP MENU” to continue through the system setup process, or simply press

the SETUP button to exit the “SETUP MENU” completely.

TO SET CHANNEL LEVELS USING THE AUTO TEST TONE FUNCTION

Press the SETUP button to enter the SETUP MENU.

The “SETUP MENU / LISTENING PROFILES” menu appears on the front panel display.

Press the ENTER button on the remote to enter the “LISTENING PROFILES” menu.

The “LISTENING PROFILES / MOVIE MODE” menu appears on the front panel display.

Press the ENTER button on the remote to enter the MOVIE MODE “Set Speaker Config”

settings menu.

The “MOVIE SPK Setting / Set Speaker Config” menu appears on the front panel display.

Press the

button on the remote until you reach “SET BALANCE” on the front panel

display.

The “MOVIE SPK Setting / Set Balance” menu appears on the front panel display.

Press the ENTER button on the remote to enter the “SET BALANCE” menu.

The “SET BALANCE / TEST MODE.....Off” menu appears on the front panel display.

Select “AUTO” within the “TEST MODE” section of the “SET BALANCE” menu.

When you select this function, the Cinema 11a's test tone automatically cycles every few

Содержание HD Surround Sound Processor Cinema 11a




























































Результаты поиска

Содержание HD Surround Sound Processor Cinema 11a

Отзывы:

Похожие инструкции для HD Surround Sound Processor Cinema 11a

Бренды по названию

Популярные бренды

Cary Audio Design HD Surround Sound Processor Cinema 11a, Руководство пользователя

Результаты поиска

Содержание HD Surround Sound Processor Cinema 11a

Отзывы:

Похожие инструкции для HD Surround Sound Processor Cinema 11a

Бренды по названию

Популярные бренды