Cary Audio Design HD Surround Sound Processor Cinema 11a Скачать руководство пользователя страница 50

Страница: 50 / 59

SETUP MENU

ADVANCED SETTINGS

The settings within the ADVANCED SETTINGS menu are as follows:

Password........................... Off / On / Change

Master Volume………………….-30dB

HDMI Audio Out................. Off / On

AV SYNC Delay .................. Off / 1-100ms (1 ms = approx. 1 foot or 1/3 meter)

Bright................................ High / Mid / Low / Off
Edit Custom Name

IR Controls ........................ Front / Rear / Both

Zone 2 IR Ctrls................... Front / Rear / Both

Rear IR Mode .................... Normal / Invert

Zone 2 IR Mode ................. Normal / Invert

TRIGGER........................... Zone 1 / Zone 2 / Zone 1 & 2
Auto Input Seek................. Off / On

Late .................................. Off / Half / Full (Dolby Digital only)

Restore Default.................. Restore Default / Restore Default OK!

TO SET PASSWORD

Setting a password allows you to keep settings from being changed by visitors, children or others

curious about your Cinema 11a.

Press the SETUP button on the remote to enter the “SETUP MENU”.

The “SETUP MENU / LISTENING PROFILES” menu appears on the front panel display.

Press the

button on the remote until you reach “ADVANCED SETTINGS” on the front

panel display.

The “SETUP MENU / ADVANCED SETTINGS” menu appears on the front panel display.

Press the ENTER button on the remote to enter the “ADVANCED SETTINGS” menu.

The “ADVANCED SETTINGS / Password” menu appears on the front panel display.

Press the ENTER button on the remote to enter the “PASSWORD MODE” menu.

The “Password / Password Mode…..Off” menu appears on the front panel display.

Use the

and

button on the remote to select the “OFF” or “ON” mode.

If you select the ON mode, you will have to key in the password the next time you enter

the SETUP menu. The Default, Preset Password from the factory is 0, 0, 0, 0.

Press the

button on the remote to select the “PASSWORD CHANGE” mode.

The “Password / Change” menu appears on the front panel display.

Press the ENTER button on the remote to enter the “ENTER OLD PASSWORD” menu.
Key-in the factory preset password (password preset 0, 0, 0, 0). The following will be

displayed on front panel as you enter password: *, *, *, *,. Next, enter the new

password you have chosen: _, _, _, _, The Cinema 11a will then ask you to re-enter your

new password:_,_,_,_. If properly completed, “Password set!” will be displayed on the

front panel display.

Содержание HD Surround Sound Processor Cinema 11a




























































Результаты поиска

Содержание HD Surround Sound Processor Cinema 11a

Отзывы:

Бренды по названию

Популярные бренды

Cary Audio Design HD Surround Sound Processor Cinema 11a, Руководство пользователя

Результаты поиска

Содержание HD Surround Sound Processor Cinema 11a

Отзывы:

Бренды по названию

Популярные бренды