Cary Audio Design HD Surround Sound Processor Cinema 11a Скачать руководство пользователя страница 18

Страница: 18 / 59

CONTROLS AND DISPLAYS

FRONT PANEL

2 3

4 5

7 8

9 10

POWER

SUR.
MODE

CES 7.1

Cinema 11a

192kHz/24 bit D/A Converter
Surround Sound Processor

AM/FM

PRO
LOGIC IIx

MASTER VOLUME

TUNER

HD RADIO

PRESET

NEO:6

MODE

INPUT

SETUP

ENTER

HDMI 1

HDMI 2

7.1 IN

POWER

• Press once to turn the power ON.

• Press again to turn the power OFF. The Cinema 11a will enter STANDBY mode and the

blue LED above the headphone jack will light.

BAND (AM)/(FM)

• Press this button to select between the AM & FM frequency bands.

BAND HDAM/HDFM (HD RADIO)

• Press this button to select between the HDAM & HDFM frequency bands.

PRESET

• Press this button to preset and recall desired broadcasting stations.

PRESET

• Press this button to preset and recall desired broadcasting stations.

INPUT SELECTOR

• Press one of these buttons to select the audio input source.

PRO LOGIC IIx

• Press this button to select either Pro Logic II decoding or Pro Logic IIx decoding

SUR. MODE

• Press this button to select the surround sound mode as part of Dolby Digital or DTS

decoding; music or movie selections.

NEO:6

• Press this button to turn the NEO:6 mode ON or OFF.

10.

CES 7.1

• Press this button to select CES 7.1 on, CES 7.1 all stereo, or CES 7.1 all mono mode.

Содержание HD Surround Sound Processor Cinema 11a




























































Результаты поиска

Содержание HD Surround Sound Processor Cinema 11a

Отзывы:

Похожие инструкции для HD Surround Sound Processor Cinema 11a

Бренды по названию

Популярные бренды

Cary Audio Design HD Surround Sound Processor Cinema 11a, Руководство пользователя

Результаты поиска

Содержание HD Surround Sound Processor Cinema 11a

Отзывы:

Похожие инструкции для HD Surround Sound Processor Cinema 11a

Бренды по названию

Популярные бренды