Cary Audio Design HD Surround Sound Processor Cinema 11a Скачать руководство пользователя страница 38

Страница: 38 / 59

MANUAL SOUND SETUP

Press the

button on the remote until you reach “SET CROSSOVER POINTS” on the

front panel display.
The “MOVIE SPK / Set Crossover Points” menu appears on the front panel display.

Use the

and

buttons on the remote to adjust the FL (Front Left) Crossover.

The crossover settings appear as follows as you scroll through them:

From 40 to 150 Hz in 10 Hz steps or FULL range.

Press the

button on the remote when you have made a selection.

Repeat step 5 for the Center, Front R, Side R, Surr BR, Surr BL, Side L and Subwoofer

speaker.

When you have finished setting the crossover points for all of the speakers within your
system, press the

button on the remote to select BACK, then press ENTER to return

to the previous “SETUP MENU” to continue through the system setup process, or simply

press the SETUP button to exit the “SETUP MENU” completely.

SET ACOUSTIC CALIBRATION ROOM EQ

Acoustic Calibration Equalization (EQ) is a kind of room equalizer for your speaker. It works by

measuring the acoustic characteristics of your room and neutralizing the ambient characteristics

that can color the original source material. This provides a 'flat' equalization setting. If you're not

satisfied with the automatic adjustment, you can also adjust these settings manually to get a
frequency balance that suits your tastes.

Setting the Acoustic Calibration Room EQ manually

If you have already completed automatically setting up your Cinema 11a using Auto Sound

SETUP press ENTER to restore to SETUP MENU. If you want to adjust your settings manually,
you can set the SET ROOM EQ manually following the directions below.

NOTE: The following selected menus appear on the Cinema 11a Display.

MOVIE SPK Setting

Set Room EQ

To set the Acoustic Calibration Room EQ manually:

Press the SETUP button on the remote to enter the SETUP MENU.

The “SETUP MENU / SPEAKER” menu appears on the front panel display.

Press the ENTER button on the remote to enter the “LISTENING PROFILES” setup menu.

The “LISTENING PROFILES / MOVIE MODE” menu appears on the front panel display.

Press the ENTER button to enter the MOVIE MODE “Set Speaker Config” settings menu.

The “MOVIE SPK Setting / Set Speaker Config” menu appears on the front panel display.

Press the

button on the remote until you reach “SET ROOM EQ” on the front panel

display.

The “LISTENING PROFILES / Set Room EQ” menu appears on the front panel display.

Press the ENTER button on the remote to enter the “SET ROOM EQ” setup menu.

The “Set Room EQ / FL 80Hz…..0.0” menu appears on the front panel display.

Содержание HD Surround Sound Processor Cinema 11a




























































Результаты поиска

Содержание HD Surround Sound Processor Cinema 11a

Отзывы:

Похожие инструкции для HD Surround Sound Processor Cinema 11a

Бренды по названию

Популярные бренды

Cary Audio Design HD Surround Sound Processor Cinema 11a, Руководство пользователя

Результаты поиска

Содержание HD Surround Sound Processor Cinema 11a

Отзывы:

Похожие инструкции для HD Surround Sound Processor Cinema 11a

Бренды по названию

Популярные бренды