background image

W

INTERIZATION

 

AND

 S

TORAGE

3827 8/04

S

ECTION

 8

on the boat, except for the optional transom hand shower and bow

and transom fresh water washdowns.

For the transom hand shower, place the shower head in a bucket

before turning on the shower faucet. This catches the antifreeze,

which can be reused. Proceed as described earlier in this step.

For the bow and transom fresh water washdowns:

a. Remove the hose(s) from the fresh water washdown fittings.

b. Place a bucket under the washdown fittings to catch the anti-

freeze, which can be reused.

c. Open the washdown faucets. When a steady stream of antifreeze

flows from the fittings, close the faucets.

6. If your boat does not have the optional grey water holding system,

pour one quart of antifreeze into the shower and each sink drain.

Otherwise, refer to 

8.3.8 Grey Water Holding System

 to winterize

the shower and sink drains.

8.3.4.3 Preparing the System for Use Again

When you remove your boat from storage and prepare to use it again,

flush the entire fresh water system with fresh water. Nontoxic antifreeze

is colored, so the water system is adequately flushed when uncolored

water flows from all of the faucets and shower heads. You may need to

fill the water tanks more than once to flush the system.

8.3.5 Raw Water Washdown

Before performing this procedure on the optional transom raw water

washdown, your boat should be pulled from the water.

Refer to

 4.3 Raw Water Washdown

 for a description of your boat’s raw

water washdown system.

1. Close the seacock that supplies the raw water washdown pump with

seawater.

2. Disconnect the end of the hose that is attached to the washdown side

of the seacock.

Open  Closed

Содержание 38 super sport



































































































































































Отзывы: