Carrier BWMAAN000050 Скачать руководство пользователя страница 26

Страница: 26 / 72

7-2 Manual Main Gas Shutoff Valve Outside

Boiler Jacket

7.3 Leak Check Gas Piping

Pressure test boiler and gas connection before placing

boiler in operation.

• Pressure test over 1/2 psig (3.5 kPa). Disconnect

boiler and its individual gas shutoff valve from

gas supply system.

• Pressure test at 1/2 psig (3.5 kPa) or less.

Isolate boiler from gas supply system by closing

manual gas shutoff valve. See fi gure 7-3.

• Locate leakage using gas detector, noncorrosive

detection fl uid, or other leak detection method

acceptable to authority having jurisdiction. Do

not use matches, candles, open fl ames, or other

methods providing ignition source.

• Correct leaks immediately and retest.

Manual Main Gas

Shutoff Valve

7 - GAS SUPPLY PIPING

7-3 Gas Shutoff Valve

Gas shutoff valve

(shown in closed

position)

DANGER

Fire Hazard. Do not use matches, candles, open

fl ames, or other methods providing ignition source.

Failure to comply will result in death or serious

injury.

n Gas

alve

Содержание BWMAAN000050









































































Результаты поиска

Содержание BWMAAN000050

Отзывы:

Carrier BWMAAN000050, Инструкция по установке, эксплуатации и обслуживанию, Страница: 26 / 72

Результаты поиска

Содержание BWMAAN000050

Отзывы: