Carrier BWMAAN000050 страница 12 Скачать руководство пользователя

Страница: 12 / 72

• Install discharge piping from safety relief valve. See

fi gure 5-2.

• Use ¾" or larger pipe.
• Use pipe suitable for temperatures of 375°F (191°C)

or greater.

• Individual boiler discharge piping shall be independent

of other discharge piping.

• Size and arrange discharge piping to avoid reducing

safety relief valve relieving capacity below minimum

relief valve capacity stated on rating plate.

• Run pipe as short and straight as possible to location

protecting user from scalding and properly drain

piping.

• Install union, if used, close to safety relief valve outlet.
• Install elbow(s), if used, close to safety relief valve

outlet and downstream of union (if used).

• Terminate pipe with plain end (not threaded).

5.4 Trim Piping

• Temperature - Pressure Gauge. Install temperature

pressure gauge using nipple, tee and bushing provided

with boiler. See fi gure 5-3.

• Drain Valve. Install drain valve using nipple, tee and

bushing provided with boiler. See fi gure 5-3.

5.5 System Piping

• Systems with automatic fi ll valves require back fl ow

prevention device.

• Single boiler system. See fi gures 5-4, 5-5, 5-6, 5-7 for

general guidance. Additional considerations:

• Control system designed for single central heating

pump. Installer responsible for integration of

multiple central heating pumps.

• Control system allows domestic hot water

prioritization. Function could be lost if central

heating pump not directly connected to control

system.

• Multiple boiler system. See fi gure 5-8 for general

guidance. Additional considerations:

• Control system requires equivalent water

temperatures entering each boiler to properly

sequence and adjust system supply temperature.

• Install multi boiler sensor kit. See "Parts, Kits &

Optional Accessories" manual for part number.

5 - HYDRONIC PIPING

FIGURE 5-3 Temperature Pressure Gauge and

Drain Valve Installations

Temperature Pressure

Gauge shown at

System Supply

Connection

Check Local Codes

For Maximum

Distance To Floor

WARNING

Burn and scald hazard. Safety relief valve could

discharge steam or hot water during operation.

Install discharge piping per these instructions.

FIGURE 5-2 Safety Relief Valve Discharge Piping

Drain Valve shown

at System Return

Connection to Boiler

Safety Relief Valve

Gas Supply

Содержание BWMAAN000050









































































Результаты поиска

Содержание BWMAAN000050

Отзывы:

Похожие инструкции для BWMAAN000050

Бренды по названию

Популярные бренды

Carrier BWMAAN000050, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание BWMAAN000050

Отзывы:

Похожие инструкции для BWMAAN000050

Бренды по названию

Популярные бренды