Carrier BWMAAN000050 страница 34 Скачать руководство пользователя

Страница: 34 / 72

FOR YOUR SAFETY READ BEFORE OPERATING

10 - OPERATING INSTRUCTIONS

10-1 Gas Shutoff Valve

OPEN POSITION

CLOSED POSITION

WARNING

If you do not follow these instructions

exactly, a fi re or explosion may result

causing property damage, personal injury

or loss of life.

• This appliance is equipped with an ignition device

which automatically lights burner. Do NOT try to

light this burner by hand.

• Before operating smell all around appliance area for

gas. Be sure to smell next to fl oor because some gas

is heavier than air and will settle to the fl oor.

• Use only your hand to turn the gas shutoff valve.

Never use tools. If valve will not turn by hand, do not

try to repair it, call a qualifi ed service technician. Force

or attempted repair may result in fi re or explosion.

• Do not use this appliance if any part has been

under water. Immediately call a qualifi ed service

technician to inspect appliance and to replace any part

of control system and any gas control which has been

under water.

10.1 OPERATING INSTRUCTIONS

Stop! Read Safety information above.

• Set thermostat to lowest setting.
• Turn "OFF" all electrical power to appliance.
• This appliance is equipped with an ignition device which

automatically lights the burner. Do not try to light

burner by hand!

• Remove upper front jacket panel.
• Turn gas shutoff valve clockwise to closed position.

Handle should be perpendicular to gas pipe.

• Wait 5 minutes for any gas to clear. Smell for gas,

including near fl oor. If you smell gas, STOP! Follow

instructions on this page: “What To Do If You Smell

Gas.” If you do not smell gas, go to next step.

• Turn gas shutoff valve counter clockwise to the

open position. Handle should be parallel to gas pipe.

• Replace upper jacket panel.
• Turn "ON" electrical power to appliance.
• Set thermostat to desired setting.
• If the appliance will not operate, follow instructions TO

TURN OFF GAS TO APPLIANCE and call your service

technician or gas supplier.

CAUTION

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.

• Do not touch any electrical switch; do not use any

phone in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow the gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fi re

department.

10.2 TO TURN OFF GAS TO APPLIANCE

• Set thermostat to lowest setting.
• Turn "OFF" all electric power to appliance if service is

to be performed.

• Remove front jacket panel.
• Turn gas shutoff valve handle clockwise to closed

position. Handle should be perpendicular to gas pipe.

• Replace front jacket panel.

Gas Shutoff Valve

Содержание BWMAAN000050









































































Результаты поиска

Содержание BWMAAN000050

Отзывы:

Похожие инструкции для BWMAAN000050

Бренды по названию

Популярные бренды

Carrier BWMAAN000050, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание BWMAAN000050

Отзывы:

Похожие инструкции для BWMAAN000050

Бренды по названию

Популярные бренды