Carrier BWMAAN000050 страница 25 Скачать руководство пользователя

Страница: 25 / 72

7.1

General

• Use piping materials and joining methods acceptable

to authority having jurisdiction. In absence of such

requirements National Fuel Gas Code, ANSI Z223.1/

NFPA 54.

• Size and install gas piping system to provide suffi cient

gas supply to meet maximum input at not less than

minimum supply pressure. See Table 5.

• Support piping with hooks straps, bands, brackets,

hangers, or building structure components to prevent or

dampen excessive vibrations and prevent strain on gas

connection. Boiler will not support piping weight.

• Use thread (joint) compound (pipe dope) suitable for

liquefi ed petroleum gas.

• Provide sediment trap up stream of gas valve.
• Install manual main shutoff valve outside of jacket. See

fi gure 7-2.

7.2 Conversion Kit Instructions

• See Gas Conversion Kit Instructions included with Boiler.

CAUTION

WHAT TO DO IF YOU SMELL GAS

• Do not try to light any appliance.
• Do not touch any electrical switches; do not use any

phones in your building.

• Immediately call your gas supplier from a neighbor’s

phone. Follow gas supplier’s instructions.

• If you cannot reach your gas supplier, call the fi re

department.

7 - GAS SUPPLY PIPING

TABLE 5: GAS SUPPLY PRESSURE

MODEL

Natural Gas

Propane

Min.

Max.

Min.

Max.

050

3.0" w.c.

(0.7 kPa)

13.5" w.c.

(3.3 kPa)

5.0" w.c.

(1.2 kPa)

13.5" w.c.

(3.4 kPa)

075

3.0" w.c.

(0.7 kPa)

13.5" w.c.

(3.3 kPa)

5.0" w.c.

(1.2 kPa)

13.5" w.c.

(3.4 kPa)

100

3.0" w.c.

(0.7 kPa)

13.5" w.c.

(3.3 kPa)

5.0" w.c.

(1.2 kPa)

13.5" w.c.

(3.4 kPa)

150

3.0" w.c.

(0.7 kPa)

13.5" w.c.

(3.3 kPa)

5.0" w.c.

(1.2 kPa)

13.5" w.c.

(3.4 kPa)

200

3.0" w.c.

(0.7 kPa)

13.5" w.c.

(3.3 kPa)

5.0" w.c.

(1.2 kPa)

13.5" w.c.

(3.4 kPa)

7-1 Gas Connection

Note: See Glossary - Piping Table 16

Gas Connection

NOTICE

Use two (2) wrenches when tightening and fi tting

to pipe boiler's threaded fi ttings. Boiler's internal

piping can be damaged if subjected to excessive

torque.

Содержание BWMAAN000050









































































Результаты поиска

Содержание BWMAAN000050

Отзывы:

Похожие инструкции для BWMAAN000050

Бренды по названию

Популярные бренды

Carrier BWMAAN000050, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание BWMAAN000050

Отзывы:

Похожие инструкции для BWMAAN000050

Бренды по названию

Популярные бренды