Carrier BWMAAN000050 страница 4 Скачать руководство пользователя

Страница: 4 / 72

1.1 Designated Use

• Hot water heating boiler.

• Indoor installation.

• Closet or alcove installation.

• Direct vent boiler.

• For use with natural gas or liquefi ed petroleum gases

(LP/propane).

1.2 The unit MUST NOT:

• Directly heat potable water. Indirect heating is acceptable.
• Heat water with non-hydronic heating system chemicals

present (example, swimming pool water).

• Exceed 50 psig (344 kPa) system pressure.

• Exceed 195°F (90.5°C) system design temperature.

1.3 Operational Features

• Modulating: 20-100%.

• Integral Dual Limit.

• Integral Low Water Cutoff (with test button).

• Outdoor Temperature Reset.

• Integral Multiple Boiler Control.

1 - INTRODUCTION

Содержание BWMAAN000050









































































Результаты поиска

Содержание BWMAAN000050

Отзывы:

Похожие инструкции для BWMAAN000050

Бренды по названию

Популярные бренды

Carrier BWMAAN000050, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание BWMAAN000050

Отзывы:

Похожие инструкции для BWMAAN000050

Бренды по названию

Популярные бренды