Carrier BWMAAN000050 страница 11 Скачать руководство пользователя

Страница: 11 / 72

5.1 General

• Install piping in accordance with authority having jurisdiction.

NOTICE

Use two (2) wrenches when tightening and fi tting

to pipe boiler's threaded fi ttings. Boiler's internal

piping can be damaged if subjected to excessive

torque.

• Support system piping and safety relief valve discharge

piping. Boiler's internal piping and wall mount bracket can

be damaged if subjected to excessive weight.

• Size central heating pump (and domestic hot water pump,

if used) for system requirements only. Heat exchanger

pump compensates for pressure drop through boiler

internal piping and heat exchanger.

• Thoroughly clean and fl ush system before connecting to

boiler.

5.2 Special Conditions

• System piping exposed to freezing conditions: Use

inhibited proplyene glycol solutions certifi ed by fl uid

manufacturer for use with closed water heating system.

Do not use automotive or ethylene glycol.

• Boiler installed above radiation level (or as required by

authority having jurisdiction). Integral low water cutoff

provided in boiler. See page 6.

• Boiler used in connection with refrigeration system.

Install piping in parallel with boiler, with appropriate

valves to prevent chilled medium from entering boiler.

• System piping connected to heating coils located in air

handling unit exposed to refrigerated air circulation.

Install fl ow control valves or other automatic means to

prevent gravity circulation of boiler water during cooling

cycle.

5.3 Safety Relief Valve and Air Vent

NOTICE

Boiler rated at 50 psig (345 kPa) maximum

allowable working pressure. Boiler provided with

30 psig (206 kPa) safety relief valve. Field source

safety relief valve for system pressures greater than

30 psig (206 kPa). Temperature Pressure Gauge

and Air Vent satisfactory for 30-50 psig (206-345

kPa) operation.

• Install safety relief valve and air vent using pipe fi ttings

provided with boiler. See fi gure 5-1

• Install safety relief valve with spindle in vertical position.
• Do not install shutoff valve between boiler and safety

relief valve.

WARNING

• Poison hazard. Ethylene glycol is toxic. Do not use

ethylene glycol.

• Never use automotive or standard glycol antifreeze,

even ethylene glycol made for hydronic systems.

• Ethylene glycol can attack gaskets and seals used in

hydronic systems.

• Use only inhibited proplyene glycol solutions certifi ed

by fl uid manufacturer as acceptable for use with closed

water heating system.

• Thoroughly clean and fl ush any system that used glycol

before installing new Boiler.

• Provide user with Material Safety Data Sheet (MSDS)

on fl uid used.

5 - HYDRONIC PIPING

NOTICE

Do not expose boiler and condensate piping to

freezing temperatures.

FIGURE 5-1 Safety Relief Valve & Air Vent (View

from front of boiler)

Air Vent

3/4" x 1/4" NPT

90° Elbow

Safety Relief

Valve

3/4"F x 3/4"M

NPT Tee

3/4" NPT

Close Nipple

3/4 NPT

Position Air Vent and Safety Relief Valve

to provide space for discharge piping.

Содержание BWMAAN000050









































































Результаты поиска

Содержание BWMAAN000050

Отзывы:

Похожие инструкции для BWMAAN000050

Бренды по названию

Популярные бренды

Carrier BWMAAN000050, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание BWMAAN000050

Отзывы:

Похожие инструкции для BWMAAN000050

Бренды по названию

Популярные бренды