Carrier BWMAAN000050 страница 29 Скачать руководство пользователя

Страница: 29 / 72

9.1 Fill boiler with water and purge air

• Fill boiler with potable water.
• Fill boiler and system piping with water (or antifreeze-

water solution, if used). See antifreeze information

page 11. Purge air from boiler using air vent. Purge

air from system piping.

• Inspect system piping and boiler connections. Repair

any leaks immediately.

9.2 Fill Condensate Trap with Water

• Disconnect collet clip from condensate hose barb. See

fi gure 9-1.

• Disconnect tubing below from hose barb.
• Pour approximately 2 cups (473 ml) of water into

condensate drain.

• Reconnect tubing to hose barb with collet clip. See

fi gure 9-1.

9 - START UP PROCEDURE

NOTICE

IMPORTANT: Condensate trap must be manually

fi lled with water at initial start up.

9-1 Condensate Drain Assembly

1. Disconnect collet clip from

hose barb and fi ll Condensate

trap with water.

2. Reconnect hose to hose

barb with collet clip before

starting boiler.

Содержание BWMAAN000050









































































Результаты поиска

Содержание BWMAAN000050

Отзывы:

Похожие инструкции для BWMAAN000050

Бренды по названию

Популярные бренды

Carrier BWMAAN000050, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание BWMAAN000050

Отзывы:

Похожие инструкции для BWMAAN000050

Бренды по названию

Популярные бренды