Carrier BWMAAN000050 страница 17 Скачать руководство пользователя

Страница: 17 / 72

6.1 General

This boiler requires a dedicated direct vent system.

Install combustion air and vent piping in accordance

with these instructions, authority having jurisdiction,

and National Fuel Gas Code, ANSI 223.1/NFPA 54.
Vent connections serving appliances vented by natural draft

shall not be connected into any portion of mechanical draft

systems operating under positive pressure.
Install vent system in accordance with these instructions.

6.2 Removal of Existing Boiler From Common

Vent System

When existing boiler is removed from common venting

system, common venting system is likely to be too large for

proper venting of appliances remaining connected to it.
After removal of existing boiler, following steps shall

be followed with each appliance remaining connected to

common venting system placed in operation, while other

appliances remaining connected to common venting system

are not in operation:

• Seal any unused openings in common venting system.
• Visually inspect venting system for proper size and

horizontal pitch. Determine there is no blockage or

restrictions, leakage, corrosion and other defi ciencies

which could cause an unsafe condition.

• When practical, close all building doors, windows, and

all doors between space in which appliances remaining

connected to common venting system are located and

other spaces of building. Turn on clothes dryer and any

appliance not connected to common venting system.

Turn on exhaust fans, such as range hoods and bath-

room exhaust so they will operate at maximum speed.

Do not operate summer exhaust fan. Close fi replace

dampers.

• Turn on appliance being inspected. Follow lighting

instructions. Adjust thermostat so appliances will operate

continuously.

• Test for spillage at draft hood relief opening after 5

minutes of main burner operation. Use fl ame of match or

candle, smoke from cigarette, cigar or pipe.

• Determine each appliance remaining connected to

common venting system properly vents when tested

as outlined above. Then return doors, windows,

exhaust fans and any other gas-burning appliance to

their previous condition of use.

6 - COMBUSTION AIR AND VENT PIPING

• Any improper operation of common venting system

should be corrected so installation conforms with National

Fuel Code, ANSI Z223.1/NFPA 54. When re-sizing any

portion of common venting system, common venting

system should be re-sized to approach minimum size as

determined using appropriate tables in Chapter 13 of the

National Fuel Gas Code, ANSI Z223.1/NFPA 54.

6.3 Materials

• See Table 3

Table 3 - Combustion air and vent pipe fi ttings

must conform with the following:

Item

Material Standards

Vent Pipe

and Fittings

PVC schedule 40

ANSI/ASTM D1785

PVC - DWV

ANSI/ASTM D2665

CPVC schedule 40

ANSI/ASTM D1784/

F441

SDR-21 & SDR-26 PVC

ANSI/ASTM D2241

ABS-DWV

ANSI/ASTM D2661

Schedule 40

ANSI/ASTM F628

Pipe

Cement/

Primer

PVC ANSI/ASTM

D2564

CPVC

ANSI/ASTM F493

Schedule 40 ABS

ANSI/ASTM D2235

• IPEX is approved vent manufacturer in Canada listed

to ULC-S636.

• IPEX System 636 Cements and Primers are approved

in Canada listed to ULC-S636.

DO NOT USE CELLULAR (FOAM) CORE PIPE

WARNING

Use of cellular core PVC for venting fl ue gas could

result in death, serious injury.

Содержание BWMAAN000050









































































Результаты поиска

Содержание BWMAAN000050

Отзывы:

Похожие инструкции для BWMAAN000050

Бренды по названию

Популярные бренды

Carrier BWMAAN000050, Инструкция по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание BWMAAN000050

Отзывы:

Похожие инструкции для BWMAAN000050

Бренды по названию

Популярные бренды