Carlo Cracco Masterpro BGMP-9146, Инструкция по эксплуатации

Страница: 15 / 91

09 10
3. Place the appropriate accessory in the unit for your selected cooking feature and close the cover.
To start preheating press START / STOP. While the device is preheating, insert the probe in the
middle of the thickest part of the largest piece of protein, close (but not touching) the bone. DO NOT
insert the probe either vertically or at an angle, as it does not provide accurate reading.
4. When the device has preheated and the "Add Food" flashes on the screen, open the cover, put
food inside the device and close the cover over the cord of the probe. The monitor will now show the
reading of the temp probe as it cooks the food.
EN EN
4. Press START/STOP to begin preheating. PRE will appear on the display screen, and the progress
bar will begin. It can take approximately 4 minutes.
5. Display will show 'Add food' when preheating is completed.
6. Open the cover and put the ingredients on the grill. When the cover is closed, cooking begins and
the timer counts down.
NOTE: If you just want to use the temp probe for testing your food’s temperature press TEMP ACE
button for 2 seconds and the internal temperature of the food will appear on the screen for 5
seconds. When the screen starts flashing, you weren't holding the button long enough. Refer to the
page about Troubleshooting.
7. The device will beep when cook time is through, and END appears on the display screen. Push
TIME up arrow and push START / STOP if you need to add more time to cook the food. When using
the detector the time change varies. Page 9, phase 6b of reference, when using the probe
.
8. Keep the cover open after removing the food, so that the machine can cool down faster. After
cooking, the stainless steel cover on the outside of the unit will be hot.
NOTE: When Cooking same food in batch, refer to the instructions at the bottom of page 7.
5. When your food inside hits the temperature you set, the device will beep and the display shows
‘End’. Press TEMP ACE button for 2 sec, the display will go on showing the internal food temperature.
6a. Temp probe cooking complete:
Remove protein from the unit, insert the probe and position it on a plate for a minimum of 5 minutes
to rest. When it is cooking, the protein should carry over to rest. If it hits the temperature of carry-over
cook on the chart from previous page you're complete with the cooking.
6b. Cooking more food without the Temp probe:
If you use the same feature to cook more food but do not need to use the probe, simply press
START/STOP to restart. Then press the TIME arrow to set a new cook time. Change the temperature
of the function, if applicable. To get started click START / STOP. If you use a different function to cook
more food, pick that function before setting the new time and temperature for cook.
NOTE: You can test the food's internal temperature at any time, even if it does not run a cook
feature. Only click the Temp button for 2 seconds.
6c. Cooking same food in batch with the Temp probe:
If you are cooking same food (meat) in batch, remove the probe from the cooked protein and place it
in the center of the largest uncooked protein portion. Click the TEMP button, set the internal tempera-
ture you want and click START / STOP. "Add Food" will show, let the device run for about 3 minutes
until the cover is opened and add the next batch of protein. Then, take step 5.
TYPES OF COOKING
Make sure the machine is plugged in before turning it on then tap the power button.
GRILL
1. Place the cooking pot on the main unit with the indent on the pot corresponding to the rear bump.
Then through the grill with the handles facing up into the bowl. Make sure the splatter guard is in
place and close the cover.
2. Tap GRILL button. The default temperature level on the left side of the control panel will light, and
the corresponding air temperature will appear on the display screen. To change the temperature
setting, press the Grill button, or the up and down TEMP arrows.
3. Click the TIME arrows up and down to set the cook time, in approximately 1 minute, up to 30
minutes, or follow the instructions on page 8 to adjust the temperature of a probe using the TEMP
ACE button.