Capacity TJ5000 DOT страница 70 Скачать руководство пользователя | Manualshive

Страница: 70 / 116

background image

Capacity of Texas, Inc.

62

729
{4}

Intake Air Heater Number 1
Circuit - Shorted Low. Low
voltage detected at the Intake
Air Heater Signal Circuit.

The intake air heaters may be
ON or OFF all of the time.

697
{3}

PWM Output Device Driver
(Transmission Shift
Modulation) - Shorted Low.
No voltage is detected when
voltage is commanded.

The engine and transmission
interface will possibly

not

function properly.

697
{4}

PWM Output Driver
(Transmission Shift
Modulation) - Shorted Low.
No voltage is detected when
voltage is commanded.

The engine and transmission
interface will possibly

not

function properly.

412
{15}

EGR Temperature - Data Valid
but Above Normal Operating
Range - Least Severe Level.

Engine power derate.

412
{16}

EGR Temperature - Data Valid
but Above Normal Operating
Range - Moderately Severe
Level.

Engine power derate.

110
{15}

Engine Coolant Temperature
High - Warning. Engine
temperature signal indicates
engine coolant temperature is
above engine protection
warning limit.

Power derate and possible
engine shutdown if engine
protection shutdown feature is
enabled.

105
{15}

Intake Manifold Air
Temperature High - Warning.
Intake manifold air
temperature signal indicates
intake manifold air
temperature is above the
engine protection warning
limit.

Engine power derate.

102
{2}

Intake Manifold Pressure -
Data Incorrect. The ECM has
detected an intake manifold
pressure signal that is too high
or low for current engine
operating conditions.

Engine power derate.

Table 4-2 CM850 System Fault Codes (Cont.)

Fault
Code

Reason

Effect

«
...
68
69
70
71
72
...
»

Содержание TJ5000 DOT





















































































































Отзывы:

Нет отзывов

Похожие инструкции для TJ5000 DOT

Бренд: Scheppach Страницы: 112

Бренд: ARBOC Страницы: 195

Бренд: Jet Страницы: 16

Бренд: Mahindra Страницы: 55

Premier CST990HD

Бренд: Sealey Страницы: 2

Бренд: Verhagen Leiden Страницы: 18

Бренд: UralAZ Страницы: 146

Бренд: URAL Motorcycles Страницы: 247

Бренд: URAL Motorcycles Страницы: 267

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды