Capacity TJ5000 DOT страница 25 Скачать руководство пользователя

Страница: 25 / 116

Trailer Jockey Operators Handbook

ECTION

PERATION

3-1 S

AFETY

RECAUTIONS

The Trailer Jockey is equipped with operator seat belts that

should be worn at all times when the vehicle is in operation.

Failure to properly wear seat belts at all times can greatly

increase the possibility of injury in an accident.

Face inward and always use grab handles when entering or

exiting the vehicle.

Keep interior of cab clean and free of obstacles or obstructions

that could impair safe operation of the vehicle.

Keep windows and mirrors clean.

Do not allow mud or road grime to accumulate on floor of cab

or exterior steps and walkways. A slippery surface is hazard-

ous.

This vehicle has been engineered and manufactured to be as

safe and trouble-free as possible. Vehicle design and the parts

used to manufacuture this vehicle undergo extensive testing

and research to guarantee that acceptable, safe service lift is

realized.

However, the vehicle owner plays an important part and

determines, in large part, the extent to which this vehicle will

provide trouble-free operation. It is the owner’s responsibility

to see that the vehicle receives proper care by following all the

prescribed scheduled maintenance procedures detailed in this

manual. Proper maintenance will ensure that parts subject to

normal wear and tear are repaired or replaced in a timely

fashion.

Содержание TJ5000 DOT





















































































































Результаты поиска

Содержание TJ5000 DOT

Отзывы:

Похожие инструкции для TJ5000 DOT

Бренды по названию

Популярные бренды

Capacity TJ5000 DOT, Руководство оператора

Результаты поиска

Содержание TJ5000 DOT

Отзывы:

Похожие инструкции для TJ5000 DOT

Бренды по названию

Популярные бренды