Capacity TJ5000 DOT страница 33 Скачать руководство пользователя

Страница: 33 / 116

Trailer Jockey Operators Handbook

3-8 I

AVE

A P

ROBLEM

Remember, even a minor defect can become serious. Report all

defective equipment immediately.

Prop shaft MUST be disconnected for towing to prevent dam-

age to transmission.

If possible, haul a defective machine to the repair area. Avoid

towing it. If towing is unavoidable, the parking brakes may be

released by pushing the cab parking brake control in, provided

adequate air pressure is available. The parking brakes may be

released manually at the rear brake chambers. These manual

releases must be removed when the towing is completed in

order to re-engage the parking brakes.

To avoid personal injury or property damage when manually

releasing the spring brakes, be sure to block the wheels so that

vehicle cannot move when the brakes are released.

Under no circumstances should a spring brake chamber

assembly be disassembled without following the procedures

described in the service manual. Bypassing these procedures

may result in severe personal injury or death.

To manually release parking brakes for towing, remove cover

plug and special bolt from housing and insert bolt in chamber

and turn 1/4 turn. Tighten nut with 3/4-inch wrench until

spring is compressed - releasing brakes.

This is an emergency procedure only. The spring brake

chamber must be returned to automatic application by

removing special bolt and replacing bolt and cap in proper

places before operating the Trailer Jockey. A flashing red light

is provided to warn the operator that the parking brake is

applied.

Содержание TJ5000 DOT





















































































































Результаты поиска

Содержание TJ5000 DOT

Отзывы:

Похожие инструкции для TJ5000 DOT

Бренды по названию

Популярные бренды

Capacity TJ5000 DOT, Руководство оператора

Результаты поиска

Содержание TJ5000 DOT

Отзывы:

Похожие инструкции для TJ5000 DOT

Бренды по названию

Популярные бренды