Capacity TJ5000 DOT Скачать руководство пользователя страница 60

Страница: 60 / 116

Capacity of Texas, Inc.

608
{2}

SAE J1587/J1922 Datalink -
Cannot Transmit. The ECM
cannot transmit over the SAE
J1587 datalink.

None on performance. Devices
on the SAE J1939 datalink
may

not

operate.

100
{1}

Engine Oil Pressure Low -
Critical. Oil pressure signal
Indicates oil pressure below
the very low engine enabled.

Power and/or speed derate and
possible engine shutdown if
engine protection shutdown
feature is protection limit.

97
{15}

Water in Fuel Indicator High -
Maintenance. Water has been
detected in the fuel filter.

Possible white smoke, loss of
power, or hard starting.

639
{2}

SAE J1939 Datalink - Cannot
Transmit. Communication
between the ECM and another
device on the SAE J1939
datalink has been lost.

None on performance. Devices
on the SAE J1939 datalink
may

not

operate.

97
{3}

Water in Fuel Sensor Circuit -
Shorted High. High voltage
detected at the Water-In-Fuel
Circuit.

None on performance. No
water-In-fuel warning
available.

97
{4}

Water in Fuel Sensor Circuit -
Shorted Low. Low voltage
detected at the Water-in-Fuel
Circuit.

None on performance. No
water-in-fuel warning
available.

558
{2}

Accelerator Pedal Idle
Validation Circuit - Data In-
correct. Idle validation signals
indicate no voltage detected
simultaneously on both idle
and off-idle validation
switches.

Engine will

only

idle.

558
{13}

Accelerator Pedal Idle
Validation Circuit - Out of
Calibration. Voltage at idle
validation on-idle and off-idle
circuit does

not

match

accelerator pedal position.

Engine will

only

idle.

Table 4-2 CM850 System Fault Codes (Cont.)

Fault
Code

Reason

Effect

Содержание TJ5000 DOT





















































































































Результаты поиска

Содержание TJ5000 DOT

Отзывы:

Capacity TJ5000 DOT, Руководство оператора, Страница: 60 / 116

Результаты поиска

Содержание TJ5000 DOT

Отзывы: