manualshive.com logo in svg

Capacity TJ5000 DOT, Руководство оператора, Страница: 90 / 116

Поделиться
Скачать
Capacity TJ5000 DOT Скачать руководство пользователя страница 90

Capacity of Texas, Inc.

82

3555
{17}

Ambient Air Density - Data 
Valid but Below Normal 
Operational Range - Least 
Severe Level. Engine torque 
has been reduced because the 
vehicle was operating at a high 
altitude condition.

Possible engine derate.

641
{15}

VGT Actuator Driver Over 
Temperature (Calculated) - 
Data Valid but Above Normal 
Operational Range - Least 
Severe Level. High internal 
VGT actuator temperature has 
been detected.

None on performance.

3249
{16}

Aftertreatment Exhaust Gas 
Temperature 2 - Data Valid but 
Above Normal Operational 
Range - Moderately Severe 
Level. The aftertreatment 
diesel particulate filter inlet 
temperature sensor reading has 
exceeded the maximum 
temperature limit.

Active aftertreatment diesel 
particulate filter regeneration 
will be disabled.

3249
{0}

Aftertreatment Exhaust Gas 
Temperature 2 - Data Valid but 
Above Normal Operational 
Range - Most Severe Level. 
The aftertreatment diesel 
particulate filter inlet 
temperature sensor reading has 
exceeded the maximum engine 
protection temperature limit.

Engine power derate. Active 
aftertreatment diesel 
particulate filter regeneration 
will be disabled.

3245
{16}

Aftertreatment Exhaust Gas 
Temperature 3 - Data Valid but 
Above Normal Operational 
Range - Moderately Severe 
Level. The aftertreatment 
diesel particulate filter outlet 
temperature sensor reading has 
exceeded the maximum 
temperature limit.

Active aftertreatment diesel 
particulate filter regeneration 
will be disabled.

Table 4-3  CM2150 System Fault Codes (Cont.)

Fault 
Code

Reason

Effect

Содержание TJ5000 DOT





















































































































Отзывы:

Нет отзывов