Capacity TJ5000 DOT страница 41 Скачать руководство пользователя

Страница: 41 / 116

Trailer Jockey Operators Handbook

3-13 T

RAILER

POTTING

ARKING

)

a. Position the trailer in the desired location. Pull out the

red trailer air supply knob to set the trailer brakes.

b. Move the fifth wheel lever to the DOWN position and

lower the trailer and fifth wheel until the trailer rests

on its landing gear. Allow the lever to return to center

position after lowering.

The trailer must rest solidly on its landing gear.

c. Disconnect the air and electrical connections from the

trailer.

d. Disengage fifth wheel manual secondary lock.

e. Push the fifth wheel release valve to UNLOCK and hold

it down. Slowly drive the Trailer Jockey away from the

trailer.

3-14 S

HUTDOWN

a. When the Trailer Jockey is positioned in its parking

area, pull out on the yellow parking brake knob to apply

the parking brakes.

b. Turn the ignition key to OFF to shut down the engine.

c. If the vehicle is to remain idle for several hours, the fuel

tank should be filled to prevent condensation.

3-15 T

OWING

Any time the Trailer Jockey is to be towed, the driveline must

be disconnected or the rear wheels lifted off the ground.

Failure to disconnect the driveline or remove the axle shafts

before towing or pushing can cause serious transmission dam-

age. The engine cannot be started by towing or pushing.

Before towing or pushing a vehicle, disconnect the driveline or

lift the drive wheels off the road. An auxiliary air supply will

usually be required to actuate the vehicle brake system.

Содержание TJ5000 DOT





















































































































Результаты поиска

Содержание TJ5000 DOT

Отзывы:

Похожие инструкции для TJ5000 DOT

Бренды по названию

Популярные бренды

Capacity TJ5000 DOT, Руководство оператора

Результаты поиска

Содержание TJ5000 DOT

Отзывы:

Похожие инструкции для TJ5000 DOT

Бренды по названию

Популярные бренды