Capacity TJ5000 DOT Скачать руководство пользователя

Страница: 69 / 116

Trailer Jockey Operators Handbook

641
{5}

Variable Geometry
Turbocharger Actuator Circuit
- Current Below Normal or
Open Circuit.

Possible low power. Power
will be removed from the
turbocharger actuator motor.

641
{4}

Variable Geometry
Turbocharger Actuator Driver
Circuit - Voltage Below
Normal, or Shorted to Low
Source.

Possible low power. Power
will be removed from the
turbocharger actuator motor.

641
{3}

Variable Geometry
Turbocharger Actuator Driver
Circuit - Voltage Above
Normal, or Shorted to High
Source.

Possible low power. Power
will be removed from the
turbocharger actuator motor.

641
{6}

Variable Geometry
Turbocharger Actuator -
Current Above Normal.
Excessive current detected at
the turbocharger actuator
motor.

Possible low power. Power
will be removed from the
turbocharger actuator motor.

641
{7}

Variable Geometry
Turbocharger Actuator -
Mechanical system

not

Responding Properly or Out of
Adjustment. Turbocharger
Actuator

not

responding or

slow to respond.

Possible low power. Power
will be removed from the
turbocharger actuator motor.

641
{2}

Variable Geometry
Turbocharger Number 1
Actuator Position Sensor - Out
of Calibration. Turbocharger
actuator failed automatic
calibration.

Variable geometry
turbocharger possible low
power. Variable geometry
turbocharger actuator will
remain either open or closed.

1209
{2}

Exhaust Gas Pressure Sensor
Circuit - Data Erratic,
Intermittent or Incorrect.
Exhaust Pressure Sensor
Circuit data invalid.

Engine power derate. EGR
valve will be closed.

729
{3}

Intake Air Heater Number 1
Circuit - Shorted High. High
voltage detected at the Intake
Air Heater Signal Circuit.

The intake air heaters may be
ON or OFF all of the time.

Table 4-2 CM850 System Fault Codes (Cont.)

Fault
Code

Reason

Effect

Содержание TJ5000 DOT





















































































































Результаты поиска

Содержание TJ5000 DOT

Отзывы:

Похожие инструкции для TJ5000 DOT

Бренды по названию

Популярные бренды

Capacity TJ5000 DOT, Руководство оператора

Результаты поиска

Содержание TJ5000 DOT

Отзывы:

Похожие инструкции для TJ5000 DOT

Бренды по названию

Популярные бренды