Capacity TJ5000 DOT страница 62 Скачать руководство пользователя

Страница: 62 / 116

Capacity of Texas, Inc.

157
{3}

Injector Metering Rail Number
1 Pressure Sensor Circuit -
Shorted High. High signal
voltage detected at the Rail
Pressure Sensor Circuit.

Power and/or speed derate.

157
{4}

Injector Metering Rail Number
1 Pressure Sensor Circuit -
Shorted Low. Low signal
voltage detected at the Rail
Pressure Sensor Circuit.

Power and/or speed derate.

558
{4}

Accelerator Pedal Idle
Validation Circuit - Shorted
Low. No voltage detected
simultaneously on both the
idle validation off-idle and on-
idle circuits.

Engine will

only

idle.

677
{3}

Starter Relay Circuit - Shorted
High. High voltage detected at
the Starter Lockout Circuit.

Either the engine will

not

start

or the engine will

not

have

Starter Lockout Protection.

677
{4}

Starter Relay Circuit - Shorted
Low. Low voltage detected at
the Starter Lockout Circuit.

Either the engine will

not

start

or the engine will

not

have

Starter Lockout Protection.

103
{16}

Turbocharger Number 1 Speed
High - Warning Level. High
turbocharger speed has been
detected.

Engine power derate. The
ECM will use an estimated
turbocharger speed.

167
{16}

Electrical Charging System
Voltage High - Warning Level.
High voltage detected by the
battery voltage monitor
feature.

Amber Warning Lamp
illuminated until high battery
voltage condition is corrected.

167
{18}

Electrical Charging System
Voltage Low - Warning Level.
Low voltage detected by the
battery voltage monitor
feature.

Amber Warning Lamp
illuminated until low battery
voltage condition is corrected.

167
{1}

Electrical Charging System
Voltage Low - Critical Level.
Very low voltage detected by
the battery volt- age monitor
feature.

Red Stop Lamp illuminated
until very low battery voltage
condition is corrected.

1378
{31}

Change Lubricating Oil and
Filter.

None on performance.
Maintenance reminder

only

Table 4-2 CM850 System Fault Codes (Cont.)

Fault
Code

Reason

Effect

Содержание TJ5000 DOT





















































































































Результаты поиска

Содержание TJ5000 DOT

Отзывы:

Похожие инструкции для TJ5000 DOT

Бренды по названию

Популярные бренды

Capacity TJ5000 DOT, Руководство оператора

Результаты поиска

Содержание TJ5000 DOT

Отзывы:

Похожие инструкции для TJ5000 DOT

Бренды по названию

Популярные бренды