manualshive.com logo in svg

Canon PowerShot G3, Руководство по обслуживанию

Поделиться
Скачать
Canon PowerShot G3 Скачать руководство пользователя страница 93

3-21

CHAPTER 3.  REPAIR INSTRUCTION

Fig. 3-21 MODE DIAL

ZOOM LEVER 
UNIT

Coat the sliding 
surface with 
Logenest Lambda 
A-74.

Coat it with 
the Dia bond 
1663G.

(1)-5

MODE DIAL SPRING

(1)-3

MODE DIAL
BASE UNIT

Projected
part

Receptacle 
hole

TOP COVER UNIT

(1)-4

MODE DIAL BALL

MODE DIAL

MODE DIAL BASE UNIT

(1)-1

(1)-1, (1)-3

MODE DIAL
CAP

MODE DIAL

MODE DIAL
CAP

(1)-3

MODE DIAL

(1)-2

XA4-9170-359

BLACK

M1.7

(SELF TAP)

3.5mm

q

q

Be careful not to 
drop the MODE 
DIAL BALL and
the MODE DIAL
SPRING

CAUTION

(1)-3

(1)-4, (1)-5

NOTE2 (Assembling)

NOTE3 (Assembling)

NOTE1 (Assembling)

2.3.1.3 MODE DIAL

(1) MODE DIAL

1. Peel off the MODE DIAL CAP from the MODE DIAL.
2. Remove the screw of 

q

.

3. Remove the MODE DIAL BASE UNIT, then remove the MODE DIAL from the TOP COVER UNIT.
4. Remove the MODE DIAL BALL.
5. Remove the MODE DIAL SPRING.

CAUTION

Be careful not to drop the MODE DIAL BALL and the MODE DIAL SPRING.

NOTE1 (Assembling)

Attach the MODE DIAL and the MODE DIAL CAP with Dia bond, and coat the sliding surface of the
MODE DIAL with Logenest Lambda A-74.

NOTE2 (Assembling)

Align the large hole and small hole of the receptacle with the large projection and small projection of the
projected part, and install the MODE DIAL.

NOTE3 (Assembling)

Insert the MODE DIAL SPRING into the hole at the side of the ZOOM LEVER UNIT, and place the
MODE DIAL BALL on top of it as shown in the illustration.

Содержание PowerShot G3


























































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды