Canon PowerShot G3 Скачать руководство пользователя страница 79

Страница: 79 / 185

3-7

CHAPTER 3. REPAIR INSTRUCTION

Fig. 3-7 SIDE COVER, CF COVER

(1)-4

(2)-3

(2)-1

(1)-3

(1)-2

(2)-3

(1)-3

SIDE COVER

JACK
COVER

Claws

JACK COVER
SHAFT

JACK COVER SHAFT

4.5mm

CD1-4854-000

DARK SILVER

M1.7

(1)-1

CF COVER

(2)-2

CF CLIPPING2
SPRING

XA4-5170-307

METAL

M1.7

(SELF TAP)

3.0mm

NOTE1 (Assembling)

NOTE2 (Assembling)

JACK COVER SHAFT does
not overflow from the hole for
inserting it.

While being careful
not to ooze the
Logenest rambda
A-74, coat it as
shown in the figure.

2.2.4 SIDE COVER, CF COVER

(1) SIDE COVER

1. Remove the screw of

2. Remove the SIDE COVER.
3. Push out the JACK COVER SHAFT with the thin stick like tweezers, and pull out the JACK COVER

SHAFT.

4. Remove the two claws and remove the JACK COVER.

NOTE1 (Assembling)

JACK COVER SHAFT is not overflow from the hole for inserting it (a dashed line).

(2) CF COVER

1. Remove the screw of

2. Remove the CF CLIPPING2 SPRING.
3. Remove the CF COVER in the direction of arrow.

NOTE2 (Assembling)

While being careful not to ooze the Logenest rambda A-74, coat it as shown in the figure.

Содержание PowerShot G3


























































































































































































Результаты поиска

Содержание PowerShot G3

Отзывы:

Бренды по названию

Популярные бренды

Canon PowerShot G3, Руководство по обслуживанию

Результаты поиска

Содержание PowerShot G3

Отзывы:

Бренды по названию

Популярные бренды