Canon PowerShot G3 Скачать руководство пользователя страница 68

Страница: 68 / 185

2-6

CHAPTER 2. TECHNICAL DESCRIPTION

Error Code

E23

E24

E25

E26

E27

E30

E50

E52

Name

CF NO SPACE

POWER ON

ERROR

FOCUS PI

ERROR

CAPTURE

TIME OUT

CF WRITE

TIME OVER

POWER OFF

ERROR

CF FORMAT

ERROR

QUICK REVIEW

ERROR

Occurrence Conditions

When the CF becomes full during writing

of photographed images to CF, writing is

repeatedly performed with the JPEG com-

pression ratio successively increased to re-

duce the size of the image file until it can

be successfully written to CF. This error

occurs when writing of the JPEG image file

fails after 10 retries at increasingly higher

compression ratios.

The same applies in the case of the Mi-

cro Drive.

The power of the imaging circuit on the

MAIN PCB ASS’Y was not detected.

The power of the LCD PCB ASS’Y was not

detected.

Detection of the focus PI (photo-interrupter)

failed.

Writing of the photograph image to SDRAM

did not end within the specified time.

Free area could not be secured in the buffer

for the photograph image within the speci-

fied time in the continuous shooting mode.

The camera power was turned OFF while

the image was being recorded to the CF

Card/Micro Drive (while the green LED was

blinking). (The error code is displayed when

the camera is next turned ON.)

This error may occur after E23.

The CF Card/Micro Drive could not be for-

matted properly.

Review of the photograph image failed.

Cause and Probable Faulty Part

MAIN PCB ASS’Y

DC/DC CONVERTER PCB ASS’Y

LCD PCB ASS’Y

HINGE UNIT

OPTICAL UNIT

MAIN PCB ASS’Y

CF CARD/MICRO DRIVE

MAIN PCB ASS’Y

The battery or DC plug was removed while

the image was being recorded to the CF

Card/Micro Drive.

→

Remedy: Restart the camera.

CF CARD/MICRO DRIVE

MAIN PCB ASS’Y

Содержание PowerShot G3


























































































































































































Результаты поиска

Содержание PowerShot G3

Отзывы:

Бренды по названию

Популярные бренды

Canon PowerShot G3, Руководство по обслуживанию

Результаты поиска

Содержание PowerShot G3

Отзывы:

Бренды по названию

Популярные бренды