Canon MultiPASS C530 Скачать руководство пользователя страница 89

Страница: 89 / 243

2-10

MultiPASS C530/C560 Chapter 2: Technical Reference

Paper feed error detection

There are three types of paper feed error which may occur:

a) No paper error

Occurs when the Paper Edge Sensor does not detect the paper’s leading edge the start

of the paper picked up operation is executed, it is executed again. If the paper is still
not sensed , it is assessed as a No paper error.

b) Eject delay jam

Occurs when the Paper Edge Sensor does not detect the paper’s trailing edge after the

page has been printed, or after 22 inches (558.8 mm) of paper eject operation has
been performed.

c) Paper size error

When the size of the paper being fed is different from that registered in the user data,

and the page being printed is divided during printing, a paper size error will occur.

When a paper feed error occurs, memory reception begins from the page at which the
paper feed error occurred.

When copying, the data are erased from memory as soon as an error occurs.

NOTE

Содержание MultiPASS C530




















































































































































































































































Результаты поиска

Содержание MultiPASS C530

Отзывы:

Похожие инструкции для MultiPASS C530

Бренды по названию

Популярные бренды

Canon MultiPASS C530, Руководство по обслуживанию

Результаты поиска

Содержание MultiPASS C530

Отзывы:

Похожие инструкции для MultiPASS C530

Бренды по названию

Популярные бренды