Canon MultiPASS C530 Скачать руководство пользователя страница 210

Страница: 210 / 243

3-53

MultiPASS C530/C560 Chapter 3: Maintenance & Service

6.2.7 Faculty tests

The faculty tests are selected by pressing the

button from the test mode menu. These tests test the

following faculties of this fax.

Test type

Overview

Sensor tests

Test whether the sensors are operating correctly.

Operation panel test

Tests whether the button switches on the control panel are
operating correctly.

Line signal reception test

Tests whether the NCU board signal sensor and frequency
counter are operating correctly.

a) Sensor tests

The sensor test is selected by pressing the

button from the faculty test menu. In this test, you can

check the status of each sensor of this fax in item 1 on the display.
You can also check if sensors that use actuators and microswitches are operating correctly by moving

the actuator or microswitch.

The sensor tests cannot be used to test all of the sensors. The following sensors cannot be

tested with the sensor tests:

Home position sensor, pickup roller sensor, and ink detection sensor.

If any of these sensor are faulty, an error message or service error code will appear to

indicate the faulty sensor.

NOTE

Содержание MultiPASS C530




















































































































































































































































Результаты поиска

Содержание MultiPASS C530

Отзывы:

Похожие инструкции для MultiPASS C530

Бренды по названию

Популярные бренды

Canon MultiPASS C530, Руководство по обслуживанию

Результаты поиска

Содержание MultiPASS C530

Отзывы:

Похожие инструкции для MultiPASS C530

Бренды по названию

Популярные бренды