Canon MultiPASS C530 Скачать руководство пользователя страница 173

Страница: 173 / 243

3-16

MultiPASS C530/C560 Chapter 3: Maintenance & Service

4.2.2 Error codes

a) Service error code output

When service data

#1 SSSW SW01

bit 0 is set to

“1”

, then service error codes are printed on the

activity management reports, reception result reports and error transmission reports, when

communication ends in an error. Also, the following is displayed, when an error occurs.

b) Error code countermeasures

From item c), all the error codes which the unit can display are listed. The separate

G3 Facsimile

Error Code List (Rev. 1)

does not specify the countermeasures for resolvable error codes. Also refer

to this list when an error code appears.
The

G3 Facsimile Error Code List

(Rev. 1)

does not specify countermeasures for all error codes.

The countermeasures that are specified in the

G3 Facsimile Error Code List (Rev. 1)

are included

here as specific countermeasures for your reference.

• Increase the transmission level

Set service data

#2 MENU

Parameter No.07 to 0 (dBm).

• Decrease the transmission level

Set service data

#2 MENU

Parameter No.07 to -15 (dBm).

• Echo measures

Change the following bit switches of service data

#1 SSSW SW03

Bit 4:1

Ignore the first DIS signal sent by the other fax machine.

Do not ignore the first DIS signal sent by the other fax machine.

Bit 5:1

Transmit a tonal signal (1850 or 1650 Hz) when the other fax machine sends a DIS signal.

Do not transmit a tonal signal when the other fax machine sends a DIS signal.

Bit 6:1

Transmit a 1850-Hz tonal signal when bit 5 is 1.

Transmit a 1650-Hz tonal signal when bit 5 is 1.

Bit 7:1

Transmit a tonal signal before sending a CED signal.

Do not transmit a tonal signal before sending a CED signal.

Display repeated

TX/RX No. 5001

START AGAIN ##106

Figure 3-8 Service Error Code Display

Содержание MultiPASS C530




















































































































































































































































Результаты поиска

Содержание MultiPASS C530

Отзывы:

Похожие инструкции для MultiPASS C530

Бренды по названию

Популярные бренды

Canon MultiPASS C530, Руководство по обслуживанию

Результаты поиска

Содержание MultiPASS C530

Отзывы:

Похожие инструкции для MultiPASS C530

Бренды по названию

Популярные бренды