Canon MultiPASS C530 Скачать руководство пользователя страница 100 | Manualshive

Страница: 100 / 243

background image

2-21

MultiPASS C530/C560 Chapter 2: Technical Reference

5.2 BJ Head Driver Block Diagram

• 128/136 bit shift resistor

Stores the printing data (HDATA) transferred from the control board at HCLOCK’s timing.

• 128/136 bit latch

Latches the printing data (HDATA) converted by the 128/136 bit shift resistor.

• Block enable decoder

After the BENB (Block enable) 1, 2, and 3 code signals are input, the specified heat timing signal is
output. The heat timing signal is divided into eighth.

• Heater (1 to 128 and 1 to 136)

The heater generates the bubbles required for the nozzles to eject the ink. The heater heats the bubble jet
nozzles. Heating is executed with the timing signal produced by the block enable decoder and the even

nozzle heat enable (EvenENB), odd nozzle heat enable (OddENB), and heat enable (HENB0 to 3)
signals.

• Sub heater

This heater maintains the optimum conditions in the nozzle for ejecting ink.

• Temperature control heater

This heater controls the head temperature to stabilize the ink ejecting amount.

• Rank resistor

To execute optimum heat control of each BJ cartridge, production-related deviation in heater
characteristics is classified into 13 types which are identified by changing the rank resistance. From the

printer MPU’s analog port, the printer MPU detects the different rank resistance as voltage values and
converts them from analog to digital for detection. The heater’s characteristics are thereby recognized.

• Head temperature sensor

Temperature changes in the nozzle’s heater are detected by the diode to prevent the bubble jet head from
overheating.

• Cartridge ID

With the ID0, ID1 and INKS2 combinations, the BJ cartridge type (color or black or photo or Multi Drop)
is recognized.

Table 2-1 Head Installation Status and Signal Detection

ID0

ID1

INKS2

Black BJ cartridge installed

Low

Low

High

Color BJ cartridge (Multi Drop) installed

High

Low

Low

Photo BJ cartridge (Multi Drop) installed

High

High

Low

Color BJ cartridge installed

High

Low

High

Photo BJ cartridge installed

High

High

High

High: Signal detected
Low: No signal detection (by printer)

«
...
98
99
100
101
102
...
»

Содержание MultiPASS C530




















































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для MultiPASS C530

Бренд: Canon Страницы: 86

Бренд: Canon Страницы: 20

KXPX2M - HOME PHOTO PRINTER

Бренд: Panasonic Страницы: 28

Бренд: Panasonic Страницы: 78

Бренд: Panasonic Страницы: 4

Бренд: Panasonic Страницы: 2

Бренд: Panasonic Страницы: 9

Jetwriter KX-CL500

Бренд: Panasonic Страницы: 32

Бренд: Xerox Страницы: 89

Бренд: olympia electronics Страницы: 4

Бренд: MakerBot Страницы: 48

Бренд: Sagem Страницы: 86

Бренд: Oki Страницы: 2

Бренд: Primera Страницы: 2

Бренд: TP Страницы: 10

Бренд: SEH Страницы: 50

WorkCentre 7655

Бренд: Xerox Страницы: 19

Бренд: Olivetti Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды