Canon MultiPASS C530 Скачать руководство пользователя страница 156

Страница: 156 / 243

2-77

MultiPASS C530/C560 Chapter 2: Technical Reference

8.5.8 Specifications for Color Communications

The operations for color communications shown below are specifications, so please take care when

fielding questions from users.

Transmission Specifications

· Even if the

Color/Black

button is pressed and the display changed between pages during transmission,

pages of BW images and pages of Color images cannot be mixed.

· Image transmission of JPEG grayscale is not possible.

· Even when

ECM TX

settings are

OFF

, this setting is ignored for color transmission, and transmission is

done automatically by ECM.

· The TTI header attached to the head of the color image is an image compression specification added

when scanning, so the time is the scanning time, not the time that transmission actually begins. This

differs from BW transmission.

· Two types of transmission mode for color transmission can be chosen: STANDARD and FINE. These

are changed by the compression ratio, depending on the quantization parameter. This varies according
to the image, but transmission in STANDARD takes approximately half the time compared to FINE

mode.

Reception Specifications

· In the

TX REPORT

settings, even when

PRINT WITH IMAGE

is set to

, the color-transmission

image is not attached. Instead a "The color fax image is not printed on this report" message is printed.

· Grayscale JPEG images sent from machines of other companies can be received.

· When an error indicating no color ink appears, a BW FAX is not automatically output even if there is

black ink available.

· When the

ECM RX

setting is

OFF

, color reception is not performed.

Other Specifications
· With framed tables, text, monochrome illustrations, etc. And sharp contrast artificial images, a small

amount of noise may occur in the image border.

· Color transmission are not supported in V3.01 of Desktop Manager.

· Because

RX REDUCTION

becomes

when the default setting

BOTTOM MARGIN

is set to

NORMAL

, the scanning width is reduced.

Содержание MultiPASS C530




















































































































































































































































Результаты поиска

Содержание MultiPASS C530

Отзывы:

Похожие инструкции для MultiPASS C530

Бренды по названию

Популярные бренды

Canon MultiPASS C530, Руководство по обслуживанию

Результаты поиска

Содержание MultiPASS C530

Отзывы:

Похожие инструкции для MultiPASS C530

Бренды по названию

Популярные бренды