Canon MultiPASS C530 Скачать руководство пользователя страница 169

Страница: 169 / 243

3-12

MultiPASS C530/C560 Chapter 3: Maintenance & Service

"CARTRIDGE JAMMED"

Printing position correction failed
Cause:

Carriage movement prevented by one of the following.

Damaged shaft.
Parts deformed. (Carriage or guide frame)

Insufficient grease.

Countermeasure:

Replace the shaft.

Replace the deformed parts.
Apply more grease.

Cause:

Bi-directional print displacement correction failed because the carriage motor
is out of step, or some similar reason.

Countermeasure:

Replace the carriage motor.

Home position error
Cause:

Foreign body in carriage section.

Countermeasure:

Open printer cover, and remove foreign body.

Cause:

Loose carriage belt.

Countermeasure:

Replace carriage belt.

Cause:

Guide frame home position detection tabs is damaged or bent parts.

Countermeasure:

Replace the damaged or bent parts.

Cause:

Carriage motor does not work.

Countermeasure:

(1) Switch power OFF/ON.
(2) Replace carriage motor.

Cause:

Carriage position cannot be detected. (Home position sensor breakdown, or BJ
controller malfunction)

Countermeasure:

(1) Switch power OFF/ON.
(2) Replace carriage cable with one that has a home position sensor attached.

(3) Replace the SPCNT board.

This error message means the same as service error codes ##338 and ##340. When this
error occurs in this model, it is not treated as a service error, but as a user error, and the

error message is displayed.

NOTE

Содержание MultiPASS C530




















































































































































































































































Результаты поиска

Содержание MultiPASS C530

Отзывы:

Похожие инструкции для MultiPASS C530

Бренды по названию

Популярные бренды

Canon MultiPASS C530, Руководство по обслуживанию

Результаты поиска

Содержание MultiPASS C530

Отзывы:

Похожие инструкции для MultiPASS C530

Бренды по названию

Популярные бренды