Canon iR2016 Series, Руководство по обслуживанию

Страница: 333 / 406

Chapter 14
14-15
14.5.2 <002: RTN transmission condition (1)><003: RTN transmission condition (2)><004: RTN transmission condition (3)>
0011-1788
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Use it to set RTN signal transmission conditions. Raise these parameters for more lenient conditions if errors occur frequently at time of reception because of trans-
mission of the RTN signal.
Memo:
Any of the following error codes may be indicated at time of reception because of RTN signal transmission
##0104, ##0107, ##0114, ##0201
RTN signal transmission condition (1) affects the ratio of error lines to the total number of lines per single page of received images.
RTN signal transmission condition (2) affects the standard value (*2) of burst errors (*1).
RTN signal condition (3) affects the number of errors not reaching the standard value of burst errors.
*1: transmission error occurring cover several lines.
*2: for instance, if '15' is set, a single burst error will represent an error occurring continuously cover 15 lines.
If any of these lines is detected while an image signal is being received, the RTN signal will be transmitted after receiving the protocol signal of the transmitting
party. Higher parameters restrict the transmission of the RTN signal.
14.5.3 <005: NCC pause length (pre-ID code)>
0011-1789
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Use it to set the length of the pause automatically entered between access code and ID code when the NCC (New Common Carrier) line is used for dialing.
14.5.4 <006: NCC pause length (post-ID code)>
0011-1790
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Use it to set the length of the pause automatically entered between ID code and telephone number of the other party when the NCC (New Common Carrier) line is
used for dialing.
14.5.5 <010: line connection identification length>
0011-1791
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Use it to set the time for identifying the line connection. Raise this parameter if errors occur frequently at time of communication because of the condition of the line.
Memo:
Any of the following error codes may be indicated because of the condition of the line
##0005, ##0018
The line condition identification time is between when the dial signal is transmitted and when the line condition is cut for the transmitting party, while it is between
when the DIS signal is transmitted and when the line is cut for the receiving party.
14.5.6 <011: T.30 T1 timer (for reception)>
0011-1792
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Set the T1 timer for the receiver (wait time after DIS transmission starts until a significant signal is received).
14.5.7 <013: T.30 EOL timer>
0011-1793
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Set it so that the 1-line transmission time is longer for reception to prevent reception errors caused by a long data length per line (e.g., computer FAX).
14.5.8 <016: time length to first response at time of fax/tel switchover>
0011-1795
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Allows setting of the time from seizing the line till pseudo RBT is sent, when the Fax/ Tel switching function is operating.
14.5.9 <017: pseudo RBT signal pattern ON time length><018: pseudo RBT signal pattern OFF time length (short)><019:
pseudo RBT signal pattern OFF time length (long)>
0011-1796
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Use it to set the pattern of the pseudo RBT signal transmitted at time of a fax/tel switchover.
14.5.10 <020: pseudo CI signal pattern ON time length><021: pseudo CI signal pattern OFF time length (short)><022:
pseudo CI signal pattern OFF time length (long)>
0011-1797
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
Use it to set the pseudo CI signal pattern transmitted at time of a fax/tel switchover.
14.5.11 <023: CNG detention level for fax/tel switchover>
0011-1798
iR2016J / iR2016 / iR2020 / / iR2016i / iR2020i
057 Display the type of soft counter 2 0 to 999
058 Display the type of soft counter 3 0 to 999
059 Display the type of soft counter 4 0 to 999
060 Display the type of soft counter 5 0 to 999
061 Display the type of soft counter 6 0 to 999
No. Item Range of settings