Canon imagePRESS C800 Series Скачать руководство пользователя страница 109 | Manualshive

Страница: 109 / 168

background image

Re-installation of the system software

Tis topic describes the re-installation of the system software on the PRISMAsync controller

NOTE

The installation process takes approximately 30 minutes.

Before you begin

• A bootable USB stick containing the system software.

Preparation of this USB stick is described in

Preparation of the USB stick on page 106

.

NOTE

If the USB stick was created with the setting to "Keep existing jobs and settings after installation"
(default setting), it not necessary to create a backup and restore.
For safety reasons we advise to create a backup. When the controller or the hard disks have to
be exchanged you will lose all settings.

Before upgrading always print the configuration report to have the Network-settings at your
disposal.

Procedure

1.

Print a configuration report

NOTE

If the system software seems to be corrupt or the HD drives have been replaced it is not possible
to execute steps 1 and 2.

2.

Create a backup of the settings and licenses

Create a backup of the settings and licenses on page 105

3.

Insert the USB stick with the system software into the USB-port of the operator panel

Make sure the PRISMAsync controller is switched on before inserting the USB stick. This is
necessary for the operating system to detect the USB stick.

4.

Restart the PRISMAsync

On the Operator Panel touch the

[Shutdown system]

button in the Setup tab of the System

section. In the next window select

[Restart]

.

The PRISMAsync will restart and boots from the stick. This can take a few minutes because the
system has to check the contents of the USB stick. After some time the PRISMAsync will reboot
and the installation process will start.
Status messages are displayed on the Operator panel. The PRISMAsync will reboot a few times
during the installation process. After installation of the software the installation wizard is
displayed.

NOTE

The software installation will take approx. 30 minutes. Do not switch off the controller during the
installation process.

5.

Remove the USB stick from the operator panel.

6.

Perform the

Installation wizard on page 27

7.

Restore the system settings and licenses

Re-installation of the system software

Chapter 9 - System software

109

«
...
107
108
109
110
111
...
»

Содержание imagePRESS C800 Series









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для imagePRESS C800 Series

Бренд: Xerox Страницы: 25

Бренд: VASTEX Страницы: 15

Бренд: GCC Technologies Страницы: 63

Бренд: GCC Technologies Страницы: 9

Бренд: GCC Technologies Страницы: 199

Бренд: Xerox Страницы: 4

Бренд: Lexmark Страницы: 455

Бренд: Lanier Страницы: 6

OKIPAGE 8p Plus

Бренд: Oki Страницы: 18

mobile pro advance

Бренд: AM TECH Страницы: 16

Бренд: Oki Страницы: 120

Бренд: Aficio Страницы: 188

Бренд: Kyocera Страницы: 2

Бренд: Code Soft Страницы: 101

Pixma G2030 Series

Бренд: Canon Страницы: 351

PIXMA G2070 Series

Бренд: Canon Страницы: 358

Бренд: Canon Страницы: 430

Бренд: Canon Страницы: 430

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды