manualshive.com logo in svg

Canon imagePRESS C800 Series, Техническое и сервисное руководство, Страница: 106 / 168

Поделиться
Скачать
Canon imagePRESS C800 Series Скачать руководство пользователя страница 106

Preparation of the USB stick

For installation of the PRISMAsync software you need a pre-programmed USB stick. This chapter
describes how to prepare the stick.

Before you begin

• a 16 GB USB stick (available via the normal service channel)
• an image of the PRISMAsync software (available via ftp-site or your service channel)
• the USB creation tool called CreateUSB (available via ftp-site or your service channel or inside

the PRISMAsync .iso file).

• a laptop or pc with Windows Vista or Windows 7

Procedure

1.

Check if .NET 4.5 is installed on the laptop. 

If .NET 4.5 not installed please download and install the .NET 4.5 framework.

2.

Insert USB key and start CreateUSB Tool.

1.

Fill out the fields in the tool. Once the .iso file is selected the tool will check if a newer version
is available (in the .iso file). If there is a new version available it will install this version and
overwrites the old one.

The following dialogue will appear:

3.

Restart the Create USB Tool. 

Restart the tool and make the settings as described below.

1.

Installation media: Browse to the location where the media .iso image is located.

2.

Product: Select the applicable product

3.

Installation of GPL media: Browse to location where the GPL media .iso image is located. This
image file contains the firmware for engine and accessories.

4.

USB drive to use: Select the USB drive to write the software.

Preparation of the USB stick

106

Chapter 9 - System software

Содержание imagePRESS C800 Series









































































































































































Отзывы:

Нет отзывов