Canon imagePRESS C800 Series Скачать руководство пользователя страница 42

Страница: 42 / 168

Engine service mode (during printing)

Introduction

In the PRISMAsync service mode it is not possible to enter Engine Service mode during printing.

To make it possible to enter the Engine Service mode for monitoring and analysis during printing
a dialogue is introduced.

NOTE

The Engine Service mode (during printing) is only accessible via the [Maintenance] tab in normal

user mode.

Engine Service mode

NOTE

The illustrations below should be used as a reference and might differ from the actual content

displayed on the user interface.

The engine service mode is for monitoring and analysis only. This mode can be used during
printing.

1. Select

[Engine Service]

to enter the engine service mode during a print run.

NOTE

This service mode is only for diagnostic and monitor purposes.
Do not change any settings in the Engine Service mode, changing settings could lead to
unpredictable machine behaviour.

2. From the engine service mode select

[Switch to normal UI]

to switch to normal user interface.

Engine service mode (during printing)

Chapter 4 - Using the PRISMAsync

Содержание imagePRESS C800 Series








































































































































































Результаты поиска

Содержание imagePRESS C800 Series

Отзывы:

Похожие инструкции для imagePRESS C800 Series

Бренды по названию

Популярные бренды

Canon imagePRESS C800 Series, Техническое и сервисное руководство

Результаты поиска

Содержание imagePRESS C800 Series

Отзывы:

Похожие инструкции для imagePRESS C800 Series

Бренды по названию

Популярные бренды