Canon imagePRESS C800 Series Скачать руководство пользователя страница 22

Страница: 22 / 168

Step

Action

Connect the other end to the connector of the Open I/F PCB on the host machine cor-
responding ports on the PRISMAsync.

Connect the Operator Attention Light

Step

Action

Install the Operator Attention Light to the backside of the host machine

Connect the cable with the 9-pins D-sub connector to the connector on the backside of
the PRISMAsync.

Connect the other side of the cable to the connector attached to the Attention Light

Connect to the network

Step

Action

Connect one side of a straight-through Ethernet cable to the

upper

RJ45 connector on

the backside of the PRISMAsync.

Connect the other side of the Ethernet cable to the Ethernet wall-outlet

Connect the power

Step

Action

Connect recessed end of the power cable to the power connector on the back of the
PRISMAsync.

Connect the other end of the power cable to a wall outlet.

Bundle the cables with a tie wrap

The PRISMAsync will be delivered with a reusable tie-wrap.

This tie wrap is used to regulate and fix all the PRISMAsync's data cables. The power cord is not
fixed with the tie wrap.

Connect the PRISMAsync

Chapter 3 - Installation

Содержание imagePRESS C800 Series








































































































































































Результаты поиска

Содержание imagePRESS C800 Series

Отзывы:

Бренды по названию

Популярные бренды

Canon imagePRESS C800 Series, Техническое и сервисное руководство

Результаты поиска

Содержание imagePRESS C800 Series

Отзывы:

Бренды по названию

Популярные бренды