Canon imagePRESS C800 Series Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 168

background image

Firmware upgrade in Safe download mode

Introduction

This topic describes the firmware upgrade of the host machine in the safe download mode. The
safe download mode can be used in case it is not possible to update the engine firmware via the
normal firmware upgrade procedure.

Firmware upgrade in safe download mode

• The firmware upgrade can be done via PRISMAsync or via an USB stick
• This procedure is applicable for both "update auto" (incremental) and "update auto disabled"

(overwrite all) mode.

• All applicable firmware files are transferred to the engine and accessories but

only engine

firmware is installed

the first time after the engine is re-booted. A second re-boot is necessary

to install the firmware on the accessories.

Before you begin

The prerequisites below are only applicable when a USB stick is used to update the firmware.
• USB Key created via SST tool.
• Create the USB key with the required firmware packages for the applicable PRISMAsync

version.

• The folder name on the USB key must be equal to the target-name reported by the engine.

Example for imagePRESS C800 series folder name is: iPRC800.

NOTE

the SST tool will take care that folder name is correct for the applicable product. When they do
not match the upgrade is aborted.

Step Action

additional Info

1

NOTE

Make sure the engine is switched off.

2

Switch on the PRISMAsync controller.
• Select [Service mode] from the splash

screen.

3

Insert the USB stick in USB slot of PRIS-
MAsync operator panel (if applicable).

NOTE

Manual upgrade must be enabled
to upgrade from a USB stick.

4

Firmware upgrade in Safe download mode

Chapter 8 - Firmware upgrades via PRISMAsync

95

«
...
93
94
95
96
97
...
»

Содержание imagePRESS C800 Series









































































































































































Отзывы:

Нет отзывов

Похожие инструкции для imagePRESS C800 Series

Бренд: SA Страницы: 5

Бренд: NCR Страницы: 36

Бренд: NCR Страницы: 206

Бренд: NCR Страницы: 138

Бренд: Ier Страницы: 8

Бренд: Olympus Страницы: 2

Бренд: QMS Страницы: 2

Бренд: Oki Страницы: 24

Бренд: Oki Страницы: 104

Бренд: Canon Страницы: 684

Бренд: J&Maya Страницы: 21

Бренд: Olivetti Страницы: 69

Бренд: Oki Страницы: 88

Бренд: Oki Страницы: 40

Бренд: Konica Minolta Страницы: 424

ThermalTronix TT-1025EX-MIL

Бренд: Intellisystem Страницы: 11

Бренд: Ricoh Страницы: 4

Бренд: Oce Страницы: 196

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды