![background image](http://html1.mh-extra.com/html/canon/imageformula-dr-9080c/imageformula-dr-9080c_service-manual_4188138152.webp)
5 - 2
COPYRIGHT © 2003 CANON ELECTRONICS INC. CANON DR-6080/9080C FIRST EDITION OCT. 2003
CHAPTER 5 TROUBLESHOOTING
Category
Code
Details
Solutions
d02
Page length double feed detection.
d04
Ultrasonic double feed detection.
Double feed
d06
Page length and ultrasonic double feed
detection.
Remove the document jam.
H01
Ink cartridge is not installed.
Install the ink cartridge.
J01
Staple detected (Feeding has stopped).
J02
Staple detected (Pick-up has stopped).
Remove the stapled
document.
J18
Skew detected.
Remove the document.
U01
Verify error (counter<number of fed sheets)
has occurred.
Check the number of
documents.
Checks
U02
Verify error (counter>number of fed sheets)
has occurred.
Check if all the documents
have been scanned.
Table 5-101b
2) List of error codes requiring a service technician
Category Code
Details
Solutions
E15
Voltage abnormalities in the imprinter
E20
Abnormalities in the main motor
E21
Abnormalities in the document tray motor
E22
Abnormalities in the retard motor
E24
Abnormalities in the feed motor
E25
Abnormalities in the pick-up motor
E26
Abnormalities in the pick-up solenoid
E27
Abnormalities in the endorser feed motor
E28
Abnormalities in the endorser printing motor
E29
Abnormalities in the registration clutch
E30
Abnormalities in the exhaust fan
E31
Abnormalities in the mechanical counter
E32
Wrong installation of main CPU PCB (The
CPU PCB for a DR-9080C has been installed
in a DR-6080 or vice versa.)
E33
Abnormalities in the shading solenoid (upper
side) connection
Hardware
connection
E34
Abnormalities in the shading solenoid (lower
side) connection
Check the
connection and
load, and replace
any required parts.
E40
Can't communicate with CPU on pick-up
control PCB (80_SUB).
E41
Can't communicate with CPU on document
tray control PCB (10_SUB).
E42
Can't communicate with CPU for imprinter.
Communication
between CPUs
E44
Can't communicate with CPU for ultrasonic
double feed detection.
Check the connection
and replace the PCB.
Table 5-102
Содержание ImageFormula DR-9080C
