manualshive.com logo in svg

Canon im2520f, Инструкции по установке, Страница: 91 / 143

Поделиться
Скачать
Canon im2520f Скачать руководство пользователя страница 91

9214

– 4 –

4511-7741-02

5. Carefully insert the Creasing Unit into the copier along the groove provided in the rear 

of the copier.

NOTE
Use care not to allow the parts shown in the illustration to hit against the mating 
portions while the Creasing Unit is being inserted.
Insert it with the Guide Plate at the finisher side facing downward shown “OK” in the 
illustration.

4511U040AA

Creasing Unit

Guide Plate

NG

OK

4511U019AA

Parts

Groove in the rear

6. Place the Creasing Unit Adjusting Plate 

beneath the Creasing Unit and temporarily 
secure the unit by tightening Screw A (1 
screw) only temporarily.

4511U020AB

7. Secure the rear end of the Creasing Unit 

using Shoulder Screw A (1 screw).

NOTE

No clearance is allowed between the 
Shoulder Screw and the metal bracket.

4511U021AA

8. Secure the Creasing Unit Adjusting Plate 

and Creasing Unit using Screw A (1 screw).

9. Securely tighten Screw A which has been 

tightened only temporarily in step 6 (1 
screw).

4511U022AB

10. Reinstall the Finisher cover and 

reinforcement plate. Mount the Finisher to 
the copier.

NOTE

For the Finisher mounting procedures, see 
Setup Instructions for 9211.

11. Remove the cover (2 screws).

4512U010AB

12. Connect the harness.

4511U023AA

4511‑7741‑02.fm  4 ページ  ２００３年１０月３日 金曜日 午前１０時１１分

Содержание im2520f
















































































































































Отзывы:

Нет отзывов