Canon im2520f Скачать руководство пользователя страница 79

Страница: 79 / 143

9211

– 6 –

4349-7741-02

5. Using Screw B, secure the ground wire.

NOTE

Make sure that the ground wire runs in the
direction shown in the illustration when
secured.

4349U034AB

6. Connect the connector.

7. Using Screw C, secure the ground wire.

4349U051AB

8. Using Screws C, secure the Secondary

Cover in position (two screws).

NOTE

Make sure that there is a uniform clearance
between the Misfeed Clearing Dial and
Secondary Cover.

4349U036AC

9. Using Screw D, secure the Secondary Cover

(one screw).

4349U037AA

10. Install the Front Cover to the copier.

4349U055AA

11. Close the Front Cover.

12. Snap the E-ring into position.

4349U052AA

13. Remove the cover from the Exit Cover that

has been removed in step 2 of “Installing the
Finisher Unit” (two screws).

4349U039AB

14. Remove the label from the Front Cover.

15. Using the screws removed in step 13, secure

the cover that has been removed in step 13
to the Front Cover (two screws).

4349U040AD

Содержание im2520f
















































































































































Результаты поиска

Содержание im2520f

Отзывы:

Canon im2520f, Инструкции по установке, Страница: 79 / 143

Результаты поиска

Содержание im2520f

Отзывы: