manualshive.com logo in svg

Canon im2520f, Инструкции по установке, Страница: 9 / 143

Поделиться
Скачать
Canon im2520f Скачать руководство пользователя страница 9

9217

– 2 –

4348-7747-02

■

Unpacking

NOTE
When removing the 2 Way Paper Feed Cabinet from its shipping carton, do not hold 
onto the reinforcement bracket (indicated by the arrow in the illustration below) (as a 
personal injury or a deformed frame could result).

1. Check that the following items are contained in the Box of Accessories.

2. Remove protective tape from different parts of the Paper Feed Cabinet.

1 Fixing Leg...............................................................................................4
2 Fixing Leg Cover ....................................................................................4
3 Fixing Bracket ........................................................................................4
4 Shoulder Screw......................................................................................4
5 Screw (9646-0408)...............................................................................12
6 Paper Size Label....................................................................................1
7 Setup Instructions (this manual).............................................................1

4348U004AA

4348U020AB

(3)

(4)

(5)

4658U021AA

4658U022AA

9646040813

4348U090CA

(7)

(6)

4348U099AB

(1)

(2)

3. Remove the protective tape from the inside 

of the drawer.

NOTE

Do not peel off the tape that fixes the Paper 
Feed Cabinet hookup harness in position 
until the copier is attached to the Paper 
Feed Cabinet.

4348U057AB

4348-7747-02.fm  Page 2  Wednesday, July 30, 2003  12:09 PM

Содержание im2520f
















































































































































Отзывы:

Нет отзывов