Canon im2520f Скачать руководство пользователя страница 134

Страница: 134 / 143

ZC3500050

– 7 –

4030-7775-02

■

Installing Covers

■

Setting the Hard Disk Drive

1. Reinstall the handle and cover to the rear of

the copier (six screws).

4599U010AA

2. Reinstall the Lower Rear Cover of the copier.

NOTE

Insert an external-tooth lock washer to the
upper right screw.

4348U018AC

4599U040AA

3. Reinstall the Rear Cover of the copier (13

screws).

NOTE

Use gold screws for the upper six.

4599U009AB

4. Reinstall the Upper Rear Cover of the copier.

NOTE

When reinstalling the Upper Rear Cover,
pass the angle detecting sensor lever into
the hole in the cover.

4599U008AB

1. Turn ON the Power Switch.
2. Call the Tech. Rep. Mode to the screen.

(For the procedure, see the Service Manual.)

3. Touch “System Input.”

4348P005CB

4. Touch “Hard Disk.”

4599P012CA

5. Touch “ON.”
6. Touch “END” on the screen that appears.

4599P008CA

7. Press the Panel Reset key.
8. Touch “Exit” on the Tech. Rep. Mode screen.
9. Turn OFF the Power Switch.

4348P005CB

Содержание im2520f
















































































































































Результаты поиска

Содержание im2520f

Отзывы:

Canon im2520f, Инструкции по установке, Страница: 134 / 143

Результаты поиска

Содержание im2520f

Отзывы: