Canon im2520f Скачать руководство пользователя страница 100

Страница: 100 / 143

ZC3500060

– 3 –

4030-7772-02

■

Installation: If 9214 is mounted

8. Plug the short connector into the empty

connector of the Finisher.

4349U054AA

9. Reinstall the Secondary Cover (two screws).

NOTE
Make sure that there is a uniform clearance
between the Misfeed Clearing Dial and
Secondary Cover.

4349U036AC

10. Reinstall the Secondary Cover (one screw).

11. Reinstall the screw for the band (one screw).

4349U037AA

1. Using Screws B, secure the Exit Tray

Mounting Holder (Right) and Exit Tray
Mounting Holder (Left) (one screw each).

4349U005AC

2. Fit the Exit Tray.

3. Secure the Exit Tray using Screws A (two

screws).

4349U006AC

4. Loosen the screws shown in the illustration,

move them in the direction of the arrow, and
then tighten them again (two screws).

NOTE

This step should be done securely.
If not, any trouble may happen.
Do not move the screw by using the Adjust
Plate. Be sure to move the screw itself.

4349U004AC

Adjust Plate

5. Open the Front Cover.

6. Remove the screw for the band (one screw).

7. Remove the Secondary Cover (three

screws).

4349U056AA

4030‑7772‑02.fm 3 ページ２００３年１０月３日金曜日午前１０時９分

Содержание im2520f
















































































































































Результаты поиска

Содержание im2520f

Отзывы:

Canon im2520f, Инструкции по установке, Страница: 100 / 143

Результаты поиска

Содержание im2520f

Отзывы: