Canon im2520f Скачать руководство пользователя страница 28

Страница: 28 / 143

im2020/im2520/im3520

– 5 –

4030-7744-02

■

Plugging in Power Cord and Turning Power ON

■

Clearing the Counters

■

ATDC Adjustment

1. Plug in the power cord to the copier.

2. Connect the power cord to a power outlet.

4030U021AA

3. Turn ON the Subswitch located on the side of

the control panel.

4030U023AA

4. Turn ON the Power Switch located on the left

side in the rear.

4030U022AA

1. Call the Tech. Rep. Mode to the screen. (For

the procedure, see the Service Manual.)

2. Select functions in this order: Tech. Rep.

Mode

→

Counter

→

PM.

3. Using the Clear key, clear “PC Life” and then

“IC Life.”

4. Touch “END.”

5. Press the Panel Reset key.

4030P007CA

1. Install the Imaging Unit (IU) in position.

2. Close the Right Door.

4030U017AB

3. Select functions in this order: Tech. Rep.

Mode

→

Function

→

F8.

4. Press the Start key to run an F8 operation.

(At this time, the Start key changes to
orange.)

5. When the Start key changes to green, touch

“END.”

6. Press the Panel Reset key.

7. Touch “Exit.”

4030P002CA

Содержание im2520f
















































































































































Результаты поиска

Содержание im2520f

Отзывы:

Canon im2520f, Инструкции по установке, Страница: 28 / 143

Результаты поиска

Содержание im2520f

Отзывы: