Canon im2520f Скачать руководство пользователя страница 125

Страница: 125 / 143

– 16 –

4513-7746-02

Scan to PC (FTP) Transmission

Scan to HDD Transmission

Scan to PC(SMTP) /IP Scanner Transmission

Network FAX Transmission

Condition

Possible Cause

Action

Cannot send.

The LAN cable is not con-
nected correctly or there is a
problem with a relay device.

Correctly connect the LAN
cable and restart or replace
the relay device.

Settings required by the device
have not been configured.

Configure the required net-
work settings (Basic Settings).

The FTP server address or
port number is not correct.

Configure the correct FTP
server address and port num-
ber settings.

The FTP server does not allow
access by anonymous users.

Enable anonymous access.

The FTP server's disk is full.

Take steps to free up disk
space.

There is a problem with the
FTP server.

Check if the FTP server is able
to communicate.

Condition

Possible Cause

Action

Cannot send.

The HDD is full.

Delete unneeded files from the
HDD and resend.

Condition

Possible Cause

Action

Cannot send.

The LAN cable is not con-
nected correctly or there is a
problem with a relay device.

Correctly connect the LAN
cable and restart or replace
the relay device.

Settings required by the device
have not been configured.

Configure the required net-
work settings (Basic Settings).

The IP address of the
addressee is not correct.

Specify the correct IP address.

Image Receiver is not running. Start up Image Receiver.

Image Receiver is not operat-
ing normally.

Restart the computer and re-
install IP Scanner.

Condition

Possible Cause

Action

Data is not reaching
the machine.

The LAN cable is not con-
nected correctly or there is a
problem with a relay device.

Correctly connect the LAN
cable and restart or replace
the relay device.

Settings required by the device
have not been configured.

Configure the required net-
work settings (Basic Settings,
Gateway Transmission).

Network FAX settings are not
correct.

Correctly configure Network
FAX settings.

Cannot send a fax from
the machine.

The addressee is not correct.

Specify the correct
addressee.

Содержание im2520f
















































































































































Результаты поиска

Содержание im2520f

Отзывы:

Canon im2520f, Инструкции по установке, Страница: 125 / 143

Результаты поиска

Содержание im2520f

Отзывы: