Canon im2520f Скачать руководство пользователя страница 22

Страница: 22 / 143

9218

– 7 –

4348-7743-03

■

Adjusting the Paper Reference Position (2)

■

Installing the Ornamental Cover

■

Affixing the Paper Size Label

1. Press the Paper Descent button and then

slide out the drawer from the Large Capacity
Cabinet.

4348U010AA

2. Open the Right Door.
3. Loosen the adjusting screw and turn screw D

clockwise or counterclockwise as necessary.

NOTE
Use care not to damage or dent the paper
path surface inside the Right Door.

4348U011AA

•

If width A is greater than the specified value,
turn screw D counterclockwise.

4002U106AA

•

If width A is smaller than the specified value,
turn screw D clockwise.

4002U105AA

4. Let the copier produce another test print and

check for the good paper reference position.

5. Make the adjustment until the specified

reference position is achieved.

6. Press the Panel Reset key to recall the Tech.

Rep. Mode to the screen.

7. Touch “Exit” on the Tech. Rep. Mode screen

to go back to the initial screen

1. Press the Paper Descent button and then

slide out the drawer from the Large Capacity
Cabinet.

2. Install the Ornamental Cover attached to the

copier (two screws).

3. Slide the drawer back in.

4348U050AA

4348U010AA

1. Affix the Paper Size Label furnished with the

Large Capacity Cabinet to the location
shown in the illustration.

4348U007AA

Содержание im2520f
















































































































































Результаты поиска

Содержание im2520f

Отзывы:

Canon im2520f, Инструкции по установке, Страница: 22 / 143

Результаты поиска

Содержание im2520f

Отзывы: