Can-Am DS 450 X mx Скачать руководство пользователя страница 98

Страница: 98 / 152

MAINTENANCE PROCEDURES

vmo2008-011-020_a

1. Air filter housing
2. Drain tube
3. Clamp

NOTE:

If vehicle is used in dusty areas,

inspect more frequently than specified
in

MAINTENANCE SCHEDULE

If liquid or deposits are found, squeeze
and remove the clamp. Pull drain tube
out then empty it.

NOTICE

Do not start engine when

liquid or deposits are found in the
drain tube.

When liquid or deposits are found,
the air filter must be inspected/dried/
replaced depending on its condition.

Remove air filter as explained in this
section.

Muffler Spark Arrester

Muffler Spark Arrester Cleaning

The muffler spark arrester must be
periodically cleaned from accumu-
lated carbon. Refer to

MAINTENANCE

SCHEDULE

The entire exhaust system should also
be visually inspected for cracks, leaks
or any damage.

CAUTION Never perform this

operation immediately after the en-
gine has been running because ex-
haust system is very hot.

Remove the spark arrester from the
muffler.

vmo2008-011-067_a

REMOVE

1. Screws

vmo2008-011-068_a

REMOVE

1. Spark arrester

Remove carbon deposits from the
spark arrester using a brush.

NOTE:

Use a soft brush and be careful

to avoid damaging spark arrester.

______________

Содержание DS 450 X mx

























































































































































Результаты поиска

Содержание DS 450 X mx

Отзывы:

Похожие инструкции для DS 450 X mx

Бренды по названию

Популярные бренды

Can-Am DS 450 X mx, Руководство оператора

Результаты поиска

Содержание DS 450 X mx

Отзывы:

Похожие инструкции для DS 450 X mx

Бренды по названию

Популярные бренды